HP 8904A - Hop the Output Signal

To Next Page

To Previous Page

Hop

the

Output

Signal

This chapter

this chapter,

you

will learn how to operate the Hop Mode

capabilities provided

Configuration Option

03.

your HP

8904A

equipped with Option

03,

this Hop Mode demonstration will teach

you how to:

Access Hop Mode Operation

Configure Channel A

for

Hopping its

Frequency,

Amplitude

and Phase Settings

Fast Hop Channel A

Set Up Your

Equipment

Connect your

8904A

to the oscilloscope

shown above.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Main Page

Table of Contents11
Volume 1 Contents14
General Information15
Description16
Safety Considerations16
Specifications17
Mechanical and Document Options and Accessories21
Options21
Electrical Options22
- Option00222
- Option 00322
- Option 00523
Accessories Supplied23
Hewlett-Packard Interface Bus23
- Option00623
- Selecting the HP-IB Address23
Documentation Updating24
- A Serial Numbers24
- Description of the Manual Update Packet24
- Signing up for the Documentation Update Service24
Recommended Test Equipment24
Initial Inspection27
Installation27
Introduction27
Preparation for Use27
- Line Voltage Selection and Fuse Replacement28
- Power Cables28
- Interconnection30
- Mating Connectors30
- Operating Environment30
- Bench Operation30
- Rack Mounting30
Storage and Shipment31
- Environment31
- Packaging31
Introduction33
Operation33
Block Diagram34
- Functional Block Descriptions35
How to Create and Output a Signal36
Instrument Functions and Operating Considerations38
- Standard Instrument: Creating a Simple Signal from Digital Data38
- How the HP 8904A Generates a Signal39
- Operating Considerations: All Instruments39
- Abbreviated Channel a Specifications40
- Option 001 . Three more Channels, Summation, Modulation, and Sequencing41
- Operating Considerations: Option 00142
- Abbreviated Specifications: Option 00142
- A Second Channel and Output44
- Operating Considerations: Option 00244
- Abbreviated Specifications: Option 00244
- Option 003 . Frequency, Amplitude, and Phase Hopping45
- Abbreviated Specifications: Option 00346
- General Information47
- Connector Hnctions47
Remote Operation50
- General Information50
- Programming Considerations50
- Status Byte63
- General Information63
Using the Status Byte63
- Error Isolation64
Error Codes and Help Messages66
Special Functions69
- Introduction69
- Special 0: Last State Recalled on Power up69
- Special 1: Disable Automatic Phase Reset69
- Special 2: Disable Beeper69
- Special 3: Reverse Modulating Waveforms69
- Special 4: Disable Output Blanking70
- Special 5: Floating Outputs on Power up70
- Special 6: Enable Synchronous Mode70
- Special 7: Configure as Master Controller70
Operating Technical Reference71
- Waveform Jitter71
- Fine Amplitude Resolution71
- Filters73
- Phase Resolution74
- Phase Continuous Switching74
Menumap76
- Selecting Menus76
- Menu Changes When Using HP-IB Control76
- Meet the HP 8904A80
- Modulate or Sum the Signals103
- Output a Sequence of Signals128
- General Description147
- HP-IB Operation147
Multi-Instrument Phase Synchronization 3A-1147
- Electrical Connections147
- Detailed Operating Instructions 3A-3149
High Power Balanced Output155
- Introduction155
- General Description155
- Operating Considerations155
Expanded Capabilities for Option157
- Output Two Signals at Once168
- Output Ports168
- Hop the Output Signal181
Equipment Required212
Introduction212
Performance Test Record212
Performance Tests212

HP 8904A - Hop the Output Signal

Table of Contents

Other manuals for HP 8904A

Related product manuals