HP ProLiant ML30 Gen10

To Next Page

To Previous Page

The installation is complete.

After installing the DIMMs, use the System Utilities > System Configuration > BIOS/Platform > Configuration (RBSU) > Memory Options

to configure the memory settings.

Installing a DIMM 106

Main Page

Table of Contents3
Component Identification8
Front Panel Components9
Front Panel Leds and Button10
Front Panel LED Power Fault Codes11
Rear Panel Components12
Rear Panel Leds13
System Board Components14
System Maintenance Switch Descriptions16
DIMM Label Identification17
DIMM Slot Locations19
PCI Expansion Slot Definitions20
Drive Leds and Buttons21
Low-Profile LFF Drive LED Definitions22
Smart Carrier (SC) Drive LED Definitions23
Drive Bay Numbering24
Fan Numbering26
Fan Mode Behavior27
Media Device Screws28
Operations29
Power up the Server30
Power down the Server31
Extend the Server from the Rack32
Remove the Server from the Rack33
Slide the Server into the Rack34
Remove the Front Bezel35
Install the Front Bezel36
Remove the Access Panel37
Install the Access Panel38
Remove the Air Baffle39
Install the Air Baffle40
Remove the PCI Slot Blank Retainer41
Remove the PCI Slot Blank42
Position the Tower Server for Hardware Configuration43
Position the Tower Server for Operation44
Setup45
Initial System Installation46
HPE Installation Service47
Setting up the Server48
Operational Requirements51
Space and Airflow Requirements52
Temperature Requirements53
Power Requirements54
Electrical Grounding Requirements55
Rack Warnings and Cautions56
Server Warnings and Cautions58
Electrostatic Discharge59
POST Screen Options60
Hardware Options Installation61
Hardware Option Installation Guidelines62
Tower to Rack Conversion Kit63
Installing the Tower-To-Rack Conversion Kit64
Preparing the Server for Rack Installation65
Installing the Rack Rails and Server Tray66
Installing the Server on the Tray70
Installing the PCI Fan and Air Baffle Options72
Power Supply Options75
Hot-Plug Power Supply Calculations76
Power Supply Warnings and Cautions77
Flexible Slot (Redundant) Power Supply Enablement Option78
Installing a Flexible Slot (Redundant) Power Supply Enablement Option79
Drive Options82
Drive Installation Guidelines83
Drive Support Information84
Installing an LFF Non-Hot-Plug Drive in the Drive Cage85
Installing an LFF Hot-Plug Drive88
Installing an SFF Hot-Plug Drive90
Media Device Options92
Installing a SAS LTO Tape Drive93
Installing a USB RDX Drive95
Installing an Optical Drive97
Installing an LFF Non-Hot-Plug Drive in the Media Drive Bay100
Memory Options103
DIMM Population Information104
Installing a DIMM105
M.2 Ssd/Dedicated Ilo/Serial Port Enablement Option107
M.2 Ssd/Dedicated Ilo/Serial Port Enablement Option Components108
Installing the M.2 Ssd/Dedicated Ilo/Serial Port Enablement Board109
Installing the Serial Port Cable113
Enabling the Dedicated Ilo Management Module116
M.2 SSD Option117
Installing an M.2 Nvme SSD on the System Board118
Installing an M.2 Nvme SSD on an M.2 Ssd/Dedicated Ilo/Serial Port Enablement Board121
Storage Controller Options123
Installing a Smart Array Standup Storage Controller124
Energy Pack Options127
HPE Smart Storage Battery127
HPE Smart Storage Hybrid Capacitor129
Minimum Firmware Versions130
Installing an Energy Pack131
Expansion Board Options134
Expansion Board Thermal Requirement135
Installing an Expansion Board136
Internal USB Device Option138
Installing an Internal USB Device139
HPE Trusted Platform Module 2.0 Gen10 Option141
Overview142
HPE Trusted Platform Module 2.0 Guidelines143
Installing and Enabling the HPE TPM 2.0 Gen10 Option144
Installing the Trusted Platform Module Board145
Preparing the Server for Installation146
Installing the TPM Board and Cover147
Preparing the Server for Operation149
Enabling the Trusted Platform Module150
Enabling the Trusted Platform Module as TPM 2.0151
Retaining the Bitlocker Recovery Key/Password153
Cabling154
Cabling Guidelines155
Storage Cabling157
LFF Non-Hot-Plug Drive Cabling from the Media Bay158
LFF Non-Hot-Plug Drive Cabling from the Drive Cage160
LFF Hot-Plug Drive Cabling162
SFF Hot-Plug Drive Cabling165
Energy Pack Cabling168
Controller Backup Power Cabling169
Media Device Cabling170
SATA Optical Drive Cabling171
SAS LTO Tape Drive Cabling172
USB RDX Drive Cabling174
Serial Port Cabling176
Fan Cabling177
Power Supply Cabling179
Front I/O Cabling181
Front USB Cabling182
Software and Configuration Utilities183
Server Mode184
Product Quickspecs185
Active Health System Viewer186
Active Health System187
Active Health System Data Collection188
Active Health System Log189
HPE Ilo 5190
Ilo Federation191
Ilo Restful API192
Restful Interface Tool193
Ilo Amplifier Pack194
Integrated Management Log195
Intelligent Provisioning196
Intelligent Provisioning Operation197
Management Security198
Scripting Toolkit for Windows and Linux199
UEFI System Utilities200
Selecting the Boot Mode201
Secure Boot202
Launching the Embedded UEFI Shell203
HPE Smart Storage Administrator204
HPE Infosight for Servers205
USB Support206
External USB Functionality207
Redundant ROM Support208
Safety and Security Benefits209
Keeping the System Current210
Updating Firmware or System ROM211
Service Pack for Proliant212
Smart Update Manager213
Integrated Smart Update Tools214
Updating Firmware from the System Utilities215
Updating the Firmware from the UEFI Embedded Shell216
Online Flash Components217
Drivers218
Software and Firmware219
Operating System Version Support220
HPE Pointnext Portfolio221
Proactive Notifications222
Troubleshooting223
NMI Functionality224
Troubleshooting Resources225
System Battery Replacement226
System Battery Information227
Removing and Replacing the System Battery228
Safety, Warranty, and Regulatory Information230
Regulatory Information231
Notices for Eurasian Economic Union232
Turkey Rohs Material Content Declaration233
Ukraine Rohs Material Content Declaration234
GS Gloss Declaration235
Warranty Information236
Specifications237
Environmental Specifications238
Server Specifications239
Power Supply Specifications240
HPE 350W E-Star 1.0 Non-Hot-Plug Power Supply (85% Efficiency)241
HPE 350W Gold Non-Hot-Plug Power Supply (92% Efficiency)242
HPE 500 W Flex Slot Platinum Hot-Plug Low Halogen Power Supply243
Websites244
Support and Other Resources245
Accessing Hewlett Packard Enterprise Support246
Clearcare Technical Support247
Accessing Updates248
Customer Self Repair249
Remote Support250
Documentation Feedback251

HP ProLiant ML30 Gen10 - Page 106

Table of Contents

Related product manuals