HPE ProLiant ML110 Gen10

To Next Page

To Previous Page

b. Remove the PCI slot blank.

10.

Install the standup storage controller.

Hardware options installation

Main Page

Table of Contents3
Component Identification7
Front Panel Components7
Front Panel Leds and Buttons8
Front Panel LED Power Fault Codes9
Rear Panel Components9
Rear Panel Leds and Button10
UID Button Functionality11
System Board Components12
System Maintenance Switch Descriptions14
DIMM Label Identification14
DIMM Slot Locations16
Pcie Slot Description16
Drives17
Low-Profile LFF Drive LED Definitions17
Hot-Plug Drive LED Definitions18
Drive Bay Numbering19
Fans21
Fan Locations22
Fan Mode Behavior22
HPE Ns204I-P Nvme os Boot Device Components23
HPE Ns204I-P Nvme os Boot Device LED Definitions23
Operations24
Power up the Server24
Power down the Server24
Remove the Server from the Rack24
Position the Tower Server for Hardware Configuration26
Remove the Access Panel26
Install the Access Panel28
Remove the Front Bezel28
Install the Front Bezel29
Remove the PCI Air Baffle30
Install the PCI Air Baffle31
Remove the System Air Baffle32
Install the System Air Baffle33
Setup35
Optional Service35
Initial Server Installation35
HPE Installation Service35
Setting up the Server36
Operational Requirements39
Space and Airflow Requirements39
Temperature Requirements39
Power Requirements40
Electrical Grounding Requirements40
Server Warnings and Cautions40
Rack Warnings and Cautions41
Electrostatic Discharge42
Setting up the Server in Tower Mode43
POST Screen Options43
Installing or Deploying an Operating System44
Hardware Options Installation45
Introduction45
Drive Options45
Drive Installation Guidelines45
Drive Support Information45
Installing an LFF Non-Hot-Plug Drive46
Installing an LFF Hot-Plug Drive48
Installing an SFF Hot-Plug Drive49
Tower-To-Rack Conversion Kit50
Installing the Tower-To-Rack Conversion Kit51
Prepare the Server for Rack Installation51
Install the Rack Rails and Server Tray52
Install the Server into the Rack55
Enable the Increased Cooling Function58
Power Supply Options58
Hot-Plug Power Supply Calculations58
Power Supply Warnings and Cautions59
Installing the ATX 550W Non-Hot-Plug Power Supply59
Redundant Power Supply Enablement Option61
Installing the Redundant Power Supply Enablement Option61
Drive Cage Options65
Installing the Four-Bay LFF Non-Hot-Plug Drive Cage65
Installing the Four-Bay LFF Hot-Plug Drive Cage67
Installing the Eight-Bay SFF Hot-Plug Drive Cage69
Installing the Optical Drive Option71
Storage Controller Options73
Storage Controller Installation Guidelines73
Installing a Standup Pcie Plug-In Smart Array Controller (Type-P)73
Configuring an HPE Smart Array Gen10 Controller77
Energy Pack Options77
HPE Smart Storage Battery78
HPE Smart Storage Hybrid Capacitor78
Installing an Energy Pack78
Expansion Board Options81
GPU Installation Requirements81
Installing an Expansion Board81
Installing the GPU Option84
Installing the HPE Ns204I-P Nvme os Boot Device Option87
HPE 12G SAS Expander Card Option91
SAS Expander Card Port Numbering91
Installing the SAS Expander Card92
Redundant Fan Option Kit95
Installing the Redundant Fans95
Memory Options98
DIMM Population Information98
DIMM-Processor Compatibility98
HPE Smartmemory Speed Information98
Installing a DIMM98
M.2 SSD Enablement Option100
Installing an M.2 SATA SSD100
Internal USB Device Option102
Installing an Internal USB Device103
Installing the Serial Port Option104
HPE Trusted Platform Module 2.0 Gen10 Option107
Overview107
HPE Trusted Platform Module 2.0 Guidelines107
Installing and Enabling the HPE TPM 2.0 Gen10 Option108
Cabling113
Cabling Guidelines113
Drive Cabling114
LFF Non-Hot-Plug Drive Cabling114
LFF Hot-Plug Drive Cabling115
SFF Hot-Plug Drive Cabling117
Storage Controller Cabling118
Storage Controller Backup Power Cabling120
SAS Expander Cabling120
Energy Pack Cabling121
Optical Drive Cabling121
M.2 SSD Cabling122
Front I/O Cabling122
Front USB 3.0 Cabling123
Ilo Service Port Cabling123
Fan Cabling124
Serial Port Cabling126
Power Supply Cabling126
Software and Configuration Utilities129
Server Mode129
Product Quickspecs129
Active Health System Viewer129
Active Health System129
HPE Ilo 5130
Ilo Federation131
Ilo Service Port131
Ilo Restful API132
Restful Interface Tool132
Ilo Amplifier Pack132
Integrated Management Log132
Intelligent Provisioning132
Intelligent Provisioning Operation133
Management Security134
Scripting Toolkit for Windows and Linux134
UEFI System Utilities134
Selecting the Boot Mode135
Secure Boot135
Launching the Embedded UEFI Shell136
HPE Smart Storage Administrator137
HPE Infosight for Servers137
USB Support137
External USB Functionality137
Redundant ROM Support138
Safety and Security Benefits138
Keeping the System Current138
Updating Firmware or System ROM138
Drivers140
Software and Firmware141
Operating System Version Support141
HPE Pointnext Portfolio141
Proactive Notifications141
System Battery Replacement142
System Battery Information142
Removing and Replacing the System Battery142
Replace the System Battery143
Troubleshooting145
NMI Functionality145
Troubleshooting Resources145
Safety, Warranty, and Regulatory Information146
Regulatory Information146
Notices for Eurasian Economic Union146
Turkey Rohs Material Content Declaration147
Ukraine Rohs Material Content Declaration147
Warranty Information147
Specifications148
Environmental Specifications148
Mechanical Specifications148
Power Supply Specifications149
ATX 350W Non-Hot-Plug Power Supply149
ATX 550W Non-Hot-Plug Power Supply (88% Efficiency)149
ATX 550W Non-Hot-Plug Power Supply (92% Efficiency)150
HPE 500W Flex Slot Platinum Hot-Plug Low Halogen Power Supply151
HPE 800W Flex Slot Platinum Hot-Plug Low Halogen Power Supply152
Websites153
Support and Other Resources154
Accessing Hewlett Packard Enterprise Support154
Clearcare Technical Support154
Accessing Updates154
Customer Self Repair155
Remote Support155
Documentation Feedback156
Acronyms and Abbreviations157

HPE ProLiant ML110 Gen10

Table of Contents

Other manuals for HPE ProLiant ML110 Gen10

Related product manuals