HUST CNC H6D-B3 - Page 55

HUST CNC H6D-B3 MANUAL
49
MCM
No.
Factory
Default
Setting
Unit Description
Setting
421 0
X-axis Origin switch (+ :N.O (normallyopen) node; -:N.C
(normally closed) node)
422 0 Y-axis Origin switch (+ :N.O node; -:N.C node)
423 0 Z-axis Origin switch (+ :N.O node; - :N.C node)
424 0 A-axis Origin switch (+ :N.O node; - :N.C node)
425 0 B-axis Origin switch (+ :N.O node; - :N.C node)
426 0 C-axis Origin switch (+ :N.O node; - :N.C node)
427 0 U-axis Origin switch (+ :N.O node; - :N.C node)
428 0 V-axis Origin switch (+ :N.O node; - :N.C node)
429 0 W-axis Origin switch (+ :N.O node; - :N.C node)
430-440
System Reserved！
441
0
X-axis, Direction of motor rotation, 0=CW, 1=CCW
442
0
Y-axis, Direction of motor rotation, 0=CW, 1=CCW
443
0
Z-axis, Direction of motor rotation, 0=CW, 1=CCW
444
0
A-axis, Direction of motor rotation, 0=CW, 1=CCW
445
0
B-axis, Direction of motor rotation, 0=CW, 1=CCW
446
0
C-axis, Direction of motor rotation, 0=CW, 1=CCW
447
0
U-axis, Direction of motor rotation, 0=CW, 1=CCW
448
0
V-axis, Direction of motor rotation, 0=CW, 1=CCW
449
0
W-axis, Direction of motor rotation, 0=CW, 1=CCW
450-460
System Reserved！
461
4
X-axis,Encoder pulse multiplicationfactor,1,2,or 4
462
4
Y-axis,Encoder pulse multiplicationfactor,1,2,or 4
463
4
Z-axis,Encoder pulse multiplicationfactor,1,2,or 4
464
4
A-axis,Encoder pulse multiplicationfactor,1,2,or 4
465
4
B-axis,Encoder pulse multiplicationfactor,1,2,or 4
466
4
C-axis,Encoder pulse multiplicationfactor,1,2,or 4
467
4
U-axis,Encoder pulse multiplicationfactor,1,2,or 4
468
4
V-axis,Encoder pulse multiplicationfactor,1,2,or 4
469
4
W-axis,Encoder pulse multiplicationfactor,1,2,or 4
470-480
System Reserved！
481 5 X-axis impulse command width adjustment (4=625KPPS)
482 5 Y-axis impulse command width adjustment (4=625KPPS)
483 5 Z-axis impulse command width adjustment (4=625KPPS)
484 5 A-axis impulse command width adjustment (4=625KPPS)
485 5 B-axis impulse command width adjustment (4=625KPPS)
486 5 C-axis impulse command width adjustment (4=625KPPS)
487 5 U-axis impulse command width adjustment (4=625KPPS)
488 5 V-axis impulse command width adjustment (4=625KPPS)
489 5 W-axis impulse command width adjustment (4=625KPPS)
490-500 6
System Reserved！
501 0
Master/Slave mode, 0=CNC, 1=X-axis, 2=Y-axis
3=Z-axis,4=A-axis,5=B-axis,6=C-axis,7=U-axis,
8=V-axis, 9=w-axis, 256= non-stop mode in a single block
502
0
Accel/Decel mode,0=exponential,1=linear,2=”S” curve
0 Home command mode setting.
BIT0 = 0 , X axis find Home grid available,
= 1 , no need to find.
BIT1 = 0 , Y axis find Home grid available,
= 1 , no need to find.
BIT2 = 0 , Z axis find Home grid available,
= 1 , no need to find.
503
BIT3 = 0 , A axis find Home grid available,
= 1 , no need to find.