Icom IC-2300H - 5 MEMORY OPERATION; Memory Channel Programming Overview; Programming a Memory Channel

Previous view
■ General description
The transceiver has 207 memory channels including 6
scan edge memory channels (3 pairs), and 1 Call chan-
nel. These channels can be individually programmed
with:
• Operating frequency (p. 5)
• Duplex direction (p. 12) and offset (p. 15)
• Subaudible tone or tone squelch and tone frequency
(pp. 13, 39–41)
• Skip setting* (p. 32)
In addition, a total of 10 memory banks; A to J, are se-
lectable for use by groups, and so on.
*except for scan edge memory channels.
Programming a memory channel ■
The VFO settings, including the Set mode contents
such as subaudible tone frequency, and so on, can be
programmed into a memory channel.
q Set the desired frequency in the VFO mode.
w Push [S.MW].
• The “ ” icon and the memory channel number blink.
e Rotate [DIAL] to select the memory channel to be
programmed.
• If the selected channel is blank, only the memory
channel number is displayed.
r Hold down [MW] (S.MW) for 1 second to program.
• 3 beeps sound.
• The memory channel number increases, when
continuing to hold down [MW] (S.MW) after pro-
gramming.
✔CONVENIENT
Memory programming can be performed in several
ways. Example; Programming the memory channel to
the same (or different) memory channel, memory chan-
nel to the Call channel, and so on.
Using the HM-133V
z Set the desired frequency in the VFO mode.
x Push [FUNC] , and then push [MW] .
• The “ ” icon and the memory channel number blink.
c Push [Y] or [Z] to select the memory channel to be
programmed. (direct numeric input cannot be used.)
v Push [FUNC] , and then hold down [MW] for
1 second to program.
➥ 3 beeps sound and the VFO contents (including
the subaudible tone frequency, and so on.) are
programmed.
➥ The memory channel number increases, when
continuing to hold down [MW] after program-
ming.
17
[i.e.]: Programming 145.870 MHz into memory chan-
nel 20 via the front panel.
[i.e.]: Programming 145.870 MHz into the memory
channel 20, using the microphone.
5
LOCK
S E T
ANM
MONI
DUP
LOW
T
-
SCAN
TONE
PRIO
M/CALL
SCAN
V/MHz
DIGITAL
PRIO
AO
BUSY
MUTE
NAR
MID
LOW
LOCK
S E T
ANM
MONI
DUP
LOW
T
-
SCAN
TONE
PRIO
M/CALL
SCAN
V/MHz
DIGITAL
PRIO
AO
BUSY
MUTE
NAR
MID
LOW
LOCK
S E T
ANM
MONI
DUP
LOW
T
-
SCAN
TONE
PRIO
M/CALL
SCAN
V/MHz
DIGITAL
PRIO
AO
BUSY
MUTE
NAR
MID
LOW
LOCK
S E T
ANM
MONI
DUP
LOW
T
-
SCAN
TONE
PRIO
M/CALL
SCAN
V/MHz
DIGITAL
PRIO
AO
BUSY
MUTE
NAR
MID
LOW
LOCK
S E T
ANM
MONI
DUP
LOW
T
-
SCAN
TONE
PRIO
M/CALL
SCAN
V/MHz
DIGITAL
PRIO
AO
BUSY
MUTE
NAR
MID
LOW
LOCK
S E T
ANM
MONI
DUP
LOW
T
-
SCAN
TONE
PRIO
M/CALL
SCAN
V/MHz
DIGITAL
PRIO
AO
BUSY
MUTE
NAR
MID
LOW
Push [V/MHz].
Rotate [DIAL] to set the frequency.
Push [S.MW].
Rotate [DIAL] to select the memory channel to be programmed.
Hold down [S.MW] for 1 second.
Beep Beep Beep
LOCK
S E T
ANM
MONI
DUP
LOW
T
-
SCAN
TONE
PRIO
M/CALL
SCAN
V/MHz
DIGITAL
PRIO
AO
BUSY
MUTE
NAR
MID
LOW
LOCK
S E T
ANM
MONI
DUP
LOW
T
-
SCAN
TONE
PRIO
M/CALL
SCAN
V/MHz
DIGITAL
PRIO
AO
BUSY
MUTE
NAR
MID
LOW
LOCK
S E T
ANM
MONI
DUP
LOW
T
-
SCAN
TONE
PRIO
M/CALL
SCAN
V/MHz
DIGITAL
PRIO
AO
BUSY
MUTE
LOCK
S E T
ANM
MONI
DUP
LOW
T
-
SCAN
TONE
PRIO
M/CALL
SCAN
V/MHz
DIGITAL
PRIO
AO
BUSY
MUTE
NAR
MID
LOW
LOCK
S E T
ANM
MONI
DUP
LOW
T
-
SCAN
TONE
PRIO
M/CALL
SCAN
V/MHz
DIGITAL
PRIO
AO
BUSY
MUTE
NAR
MID
LOW
LOCK
S E T
ANM
MONI
DUP
LOW
T
-
SCAN
TONE
PRIO
M/CALL
SCAN
V/MHz
DIGITAL
PRIO
AO
BUSY
MUTE
NAR
MID
LOW
Beep Beep Beep
Push .
Push .
Push , and then .
Push / .
Push , and then hold down for 1 second.
MEMORY OPERATION