Previous view
21
5
MEMORY OPERATION
■ Programming channel names
Each memory channel and the Call channel can be
programmed with an alphanumeric channel name, for
easy recognition. Names can be a maximum of 6 char-
acters— see the table to the right, for the selectable
characters.
q Push [M/CALL] to select the memory mode.
w
Rotate
[DIAL]
to select the desired memory channel.
e Hold down [ANM] (MONI) for 1 second to switch the
channel name display.
• Two beeps sound.
• The name is displayed, if programmed.
r Push [SET] to enter the channel name programming
mode.
t Rotate [DIAL] to select a character.
• The selected character blinks.
y Push [SET] or [MONI] to move the cursor to the left
or right.
u Repeat steps t and y, until the desired channel
name is completed.
i Push any key other than [SET] or [MONI], to pro-
gram the name and exit the channel name program-
ming mode.
• To switch to the frequency display, hold down
[MONI] (ANM) for 1 second again.
IMPORTANT!: While the channel name display
mode is selected, and when [SET] is pushed, the
channel name programming mode is always ac-
cessed.
To access the Set mode, cancel the channel name
display by holding down [MONI] (ANM) for 1 second.
Using the HM-133V
z Select the memory or Call channel to be assigned
the memory name.
x Push [FUNC] , and then push [ANM] .
• The name is displayed, if programmed.
c Push [SET] .
v Push [Y] or [Z] to select the desired character.
• The selected character blinks.
b Push [SET] or [ENT]
to move the cursor to
the left or right.
n Repeat steps v and b until the desired channel
names are completed.
m Push [CLR] to program the name and exit the
channel name programming mode.
, If desired, push [FUNC] , and then push [ANM]
to return to the frequency display.
(1)
(B)
(L)
(V)
(+) (,) (.)
(2)
(C)
(
M
)
(
W
)
(–)
(3)
(
D
)
(N)
(X)
(=)
(4)
(E)
(O)
(Y)
(✱)
(5)
(%)
(&)
(’)
(F)
(P)
(Z)
(/)
(]) (^)
(:) (;) (<) (>) (?)
(@) ([) (\)
(6)
(G)
(
Q
)
(space)
(7)
(()
(
H
)
(
R
)
())
(8)
(I)
(S)
(!) (”) (#) ($)
(9)
(J)
(T)
(0)
(A)
(
K
)
(U)
[i.e.]: Programming “CLUB” into memory channel 5.
LOCK
S
E
T
ANM
MONI
DUP
LOW
T
-
SCAN
TONE
PRIO
M/CALL
SCAN
V/MHz
DIGITAL
PRIO
AO
BUSY
MUTE
NAR
MID
LOW
PRIO
M/CALL
SCAN
V/MHz
PRIO
AO
BUSY
LOCK
S
E
T
ANM
MONI
DUP
LOW
T
-
SCAN
TONE
PRIO
M/CALL
SCAN
V/MHz
DIGITAL
PRIO
AO
BUSY
MUTE
NAR
MID
LOW
S
E
T
ANM
MONI
DUP
LOW
PRIO
M/CALL
SCAN
V/MHz
PRIO
AO
BUSY
LOCK
S
E
T
ANM
MONI
DUP
LOW
MUTE
NAR
MID
LOW
LOCK
S
E
T
ANM
MONI
DUP
LOW
T
-
SCAN
TONE
PRIO
M/CALL
SCAN
V/MHz
DIGITAL
PRIO
AO
BUSY
MUTE
NAR
MID
LOW
Push any other keys than [SET] or [MONI].
Select memory channel 5, and then hold down [ANM] (MONI) for 1 second.
Rotate [DIAL] to select the character,
and then push [SET] or [MONI] to move the cursor.
Repeat until the name is complete.
Push [SET].
Channel name display
(The name is displayed, if programmed.)
[i.e.]: Programming “CLUB” into memory channel 5.
LOCK
S
E
T
ANM
MONI
DUP
LOW
T
-
SCAN
TONE
PRIO
M/CALL
SCAN
V/MHz
DIGITAL
PRIO
AO
BUSY
MUTE
NAR
MID
LOW
PRIO
M/CALL
SCAN
V/MHz
PRIO
AO
BUSY
LOCK
S
E
T
ANM
MONI
DUP
LOW
T
-
SCAN
TONE
PRIO
M/CALL
SCAN
V/MHz
DIGITAL
PRIO
AO
BUSY
MUTE
NAR
MID
LOW
S
E
T
ANM
MONI
DUP
LOW
PRIO
M/CALL
SCAN
V/MHz
PRIO
AO
BUSY
LOCK
S
E
T
ANM
MONI
DUP
LOW
MUTE
NAR
MID
LOW
LOCK
S
E
T
ANM
MONI
DUP
LOW
T
-
SCAN
TONE
PRIO
M/CALL
SCAN
V/MHz
DIGITAL
PRIO
AO
BUSY
MUTE
NAR
MID
LOW
Select memory channel 5, push then .
Push .
Push / to select the character
,
and then push or to move the cursor.
Repeat until the name is complete.
Push .
Channel name display
(The name is displayed, if programmed.)
To Next Page
Loading...
