Icom IC-7300 - Page 34

4
RECEIVING AND TRANSMITTING
4-4
6HOHFWLQJWKH,)¿OWHU
7KHWUDQVFHLYHUKDV,)¿OWHUSDVVEDQGZLGWKVIRUHDFK
mode, and you can select them on the FILTER screen.
<RXFDQVHWWKH,)¿OWHUWRZLGH),/PLG),/RU
narrow (FIL 3).
1. Select the operating mode.
  ([DPSOH86%
2. Touch the filter icon for 1 second.
• 2SHQVWKH),/7(566%VFUHHQ
3. Touch the filter icon more times to select FIL 1
(wide), FIL 2 (mid) or FIL 3 (narrow).
4. 7RXFK>%:@
• Selects the passband width mode.
5. Rotate
MAIN DIAL
to select the passband width.
LYou cannot change the passband width in the FM or
FM-D mode.
L:KHQ\RXFKDQJHWKHSDVVEDQGZLGWKWKH7ZLQ3%7
setting value is reset to the center position.
),/7(566%VFUHHQZKHQ),/LVVHOHFWHG
Passband width mode
Touch for 1
second to reset
to default.
Displayed when a band width less than 500 H
LVVHOHFWHGLQWKH66%RU&:PRGH
6. 7RXFK>%:@
• Cancels the passband width mode.
7. Repeat steps 2 to 6 to set the passband width for
other modes except for the FM and FM-D.
8. To close the FILTER screen, push
EXIT
.
TIP:KHQ\RXVHWWKH,)¿OWHUWR),/RU),/LQWKH)0
mode, the transceiver will transmit in the FM narrow mode.
0RGH ,)¿OWHU 6HOHFWDEOHUDQJHVWHSV
66%
FIL 1 3.0 kH )
50H to 500H (50 H )
600H to 3.6kH (100 H )
FIL 2 2.4 kH )
FIL 3 1.8 kH )
66%'
CW
FIL 1 1.2 kH )
50H to 500H (50 H )
600H to 3.6kH (100 H )
FIL 2 500 H )
FIL 3 250 H )
RTTY
FIL 1 2.4 kH )
50H to 500H (50 H )
600H to 2.7kH (100 H )
FIL 2 500 H )
FIL 3 250 H )
AM
AM-D
FIL 1 .0 kH )
200H to 10.0kH (200 H )FIL 2 6.0 kH )
FIL 3 3.0 kH )
FM
FM-D
FIL 1 15 kH )
FixedFIL 2 10 kH )
FIL 3 7.0 kH )
6HOHFWLQJWKH,)¿OWHUVKDSH
<RXFDQLQGHSHQGHQWO\VHOHFWWKH'63¿OWHUVKDSHIRU
operating modes to soft or sharp.
1. 6HWWKHRSHUDWLQJPRGHWR66%66%'RU&:
  ([DPSOH86%
2. Touch the filter icon for 1 second.
• Opens the FILTER screen.
3. Touch the filter icon several times to select FIL1
(wide), FIL2 (mid) or FIL3 (narrow).
4. Touch [SHARP] or [SOFT].
5. To close the FILTER screen, push
EXIT
.
When [SOFT] is selected