Icom IC-7300 - Connectors

8
SET MODE
8-5
Connectors
ACC/USB Output Select (Default AF)
Selects the signal output from [ACC] and [USB].
ACC/USB AF Output Le el 'HIDXOW
Sets the AF output level of [ACC] and [USB].
ACC/USB AF SQL (Default OFF (OPEN))
6HOHFWVZKHWKHURUQRWWRRXWSXWWKHDXGLRIURP>$&&@
and [USB], according to the squelch state.
The same audio signals are output from [USB] and
[ACC].
ACC/USB AF Beep/Speech... Output (Default OFF)
Sets the Beep and Speech audio output condition of
[ACC] and [USB]
.
L<RXVKRXOGVHWWKH³$&&86%$)64/´LWHPWR³$)´
L7KHEHHSOHYHOLVOLPLWHGZKHQWKH³%HHS/HYHO
Limit” item is “ON.”
ACC/USB IF Output Le el 'HIDXOW
Sets the IF output level of [ACC] and [USB].
ACC MOD Le el 'HIDXOW
Sets the modulation input level of [ACC].
USB MOD Le el 'HIDXOW
Sets the modulation input level of [USB].
DATA OFF MOD (Default MIC,ACC)
Selects the connector(s) to input the modulation signal
ZKHQWKHGDWDPRGHLV2))
DATA MOD
(Default ACC)
Selects the connector(s) to input the modulation signal
ZKHQWKHGDWDPRGHLV21
External Keypad VOICE (Default OFF)
Enables voice memory transmission using an external
keypad.
External Keypad KEYER (Default OFF)
Enables keyer memory transmission using an external
keypad.
External Keypad RTTY (Default OFF)
Enables RTTY memory transmission using an
external keypad.
CI-V Baud Rate (Default Auto)
Selects the CI-V data transfer rate.
LWhen “Auto” is selected, the baud rate is
automatically set according to the data rate of the
connected controller.
CI-V Address 'HIDXOWK
Selects the CI-V address.
L³K´LVWKHGHIDXOWDGGUHVVRI,&
CI-V Transcei e (Default ON)
Turns the Transceive function ON or OFF.
&,986%ĺ5(027(7UDQVFHLYH$GGUHVV'HIDXOWK
Sets the address used to remotely control the
transceiver or receiver using the optional RS-BA1,
through the [USB] port.
The external equipment control signal is output from
the [REMOTE] port.
CI-V Output (for ANT) (Default OFF)
Enables outputting the antenna controller status
(frequency and so on) from the [REMOTE] port.
L$GGUHVV³K´LVUHVHUYHG
7KHXVDEOHDGGUHVVHVDUHOLPLWHGWRKa')K
CI-V USB Port (Default Link to [REMOTE])
6HOHFWVWKHLQWHUQDOFRQQHFWLRQW\SHEHWZHHQWKH
[USB] and [REMOTE] CI-V ports.
CI-V USB Baud Rate (Default Auto)
6HOHFWVWKH&,9GDWDWUDQVIHUUDWHZKHQUHPRWHO\
FRQWUROOLQJWKH,&WKURXJKWKH
[USB] CI-V port .
LWhen “Auto” is selected, the baud rate is
automatically set according to the data rate of
external controller.
L7KLVVHWWLQJLVYDOLGRQO\ZKHQWKH³&,986%3RUW´
item is set to “Unlink from [REMOTE].”
CI-V USB Echo Bac (Default OFF)
7XUQVWKH'DWD(FKR%DFNIXQFWLRQ21RU2))ZKHQ
UHPRWHO\FRQWUROOLQJWKH,&WKURXJKWKH>86%@
CI-V port.
L7KLVVHWWLQJLVYDOLGRQO\ZKHQWKH³&,986%3RUW´
item is set to “Unlink from [REMOTE].”
USB Serial Function (Default CI-V)
Selects the signal output from [USB].