Icom IC-9700 - Page 10

1
PANEL DESCRIPTION
1-2
Front panel (Continued)
!8 EXIT KEY
EXIT
(p� 1-6)
Exits a setting screen or returns to the previous
screen.
!9 AFC/AUTO TUNE KEY
AFC
/
AUTO
TUNE
(p� 4-1)
z In the FM or DV mode, turns the Auto
Frequency Control function ON or OFF.
z In the CW mode, automatically tunes the
operating frequency to a close-by CW signal.
@0 SPEECH/LOCK KEY
SPEECH
(p� 3-9)
Announces the operating frequency or receiving
mode, or electronically locks
MAIN DIAL
.
@1 FRICTION ADJUSTER
Adjusts the friction of
MAIN DIAL
.
@2 MAIN DIAL
MAIN DIAL
(p� 3-3)
Changes the operating frequency.
@3 TONE/RX CALL SIGN CAPTURE KEY
TONE
RX
→
CS
z In the FM mode, displays the Tone Set window.
For European versions: While holding down
[PTT], hold down this key to send the 1750 Hz tone.
z In the DV mode, push to display the RX History
list, or hold down for 1 second to capture the
latest received call sign (station or repeater) as
a temporary call destination.
@4 MEMO PAD KEY
MPAD
Sequentially calls up the contents in the Memo
Pads, or saves the displayed contents into the
Memo Pad.
@5 VFO/MEMORY KEY
V/M
(p� 3-1)
Switches between the VFO and Memory mode, or
copies the memory channel contents to the VFO.
@6 A/B KEY
A/B
(p� 3-1)
Switches between VFO A and VFO B, or copies the
selected VFO’s frequency, mode and lter settings
to the other VFO.
@7 PASSBAND TUNING CONTROL KEY
PBT
(p� 4-3)
Enables
MULTI
to adjust the Passband Tuning
Control (PBT).
@8 kHz TUNING STEP/M-CH KEY
kHz
M-CH
(p� 4-1)
In the VFO mode, push to enable
MULTI
to adjust
the kHz Tuning Control, or hold down for 1 second
to enable
MULTI
to select the Memory Channel.
L In the Memory or Call channel mode, it only
enables the Memory channel selection.
@9 RIT KEY
RIT
(p� 4-1)
Enables
MULTI
to adjust the Receiver Incremental
Tuning (RIT), and it turns the Receiver Incremental
Tuning (RIT) function ON or OFF.
#0 SPLIT KEY
SPLIT
(p� 4-10)
Turns the Split function ON or OFF.
#1 MULTI-FUNCTION CONTROL
MULTI
/
CLR
(p� 1-6)
z Displays the Multi-function menu for various
adjustments, or selects a desired item.
z Hold down for 1 second to clear the RIT shift
frequency or the PBT setting.
#2 SCAN KEY
SCAN
Displays the Scan Select window, or starts the
previously selected scan.
#3 TRANSMIT FREQUENCY CHECK KEY
XFC
(p� 4-9)
z In the Split or Duplex mode, enables you to
monitor the transmit frequency while holding the
key down.
z In Simplex mode, temporally opens the squelch
and cancels the noise reduction function while
holding the key down.
L In the DV mode, enables you to monitor signals in
the FM or DV mode, depending on the Digital Monitor
setting.
#4 TX/RX INDICATOR (p� 3-9)
Lights red while transmitting and lights green while
receiving.
#0 @7@9 @8
!8 @0
@1
!9
@2
@3
@4
#4
#3
#1
#2
@5
@6