Integra DTR-20.2 User Manual

48
En
■ TV Control
` Off:
TV Control disabled.
` On
:
TV Control enabled.
Set to “On” when you want to control the AV receiver
from an p-compatible TV that is connected to
HDMI.
Note
• Do not assign the component connected with the HDMI input to
the TV/CD selector when you set “TV Control” setting to “On”.
Otherwise, appropriate CEC (Consumer Electronics Control)
operation is not guaranteed.
•Set to
“Off” when the TV is not compatible or when it is unclear
whether the TV is compatible or not.
•The
“TV Control” setting can be set only when the “HDMI
Control
” (➔ 47) and “Power Control” settings are both set
to “On”.
• Refer to the connected component’s instruction manual for
details.
With this preference, you can protect your settings by
locking the setup menus.
Main menu Lock Setup
■ Setup
` Locked:
Setup menus locked.
` Unlocked
:
Setup menus not locked.
When the setup menus are locked, you cannot change any
setting.
You can change various audio settings from the Home
menu (➔ 22).
Note
These settings are disabled when:
• a pair of headphones is connected, or
•the “Audio TV Out” setting is set to “On” (➔ 47) and an input
selector other than HDMI is selected.
Tone Control Settings
You can adjust the bass and treble for the front speakers,
except when the Direct, or THX listening mode is
selected.
■ Bass
` –10dB to 0dB
to +10dB in 2 dB steps.
You can boost or cut low-frequency sounds output
by the front speakers.
■ Treble
` –10dB to 0dB
to +10dB in 2 dB steps.
You can boost or cut high-frequency sounds output
by the front speakers.
Note
• To bypass the bass and treble tone circuits, select the Direct, or
THX listening mode.
• Alternatively, you can use the AV receiver’s Tone and +/–
(➔ 50).
Speaker Levels
You can adjust the volume of each speaker while listening
to an input source.
These temporary adjustments are cancelled when the AV
receiver is set to Standby. To save the setting you made
here, go to “Level Calibration” (➔ 38) before setting the
AV receiver to Standby.
■ Subwoofer Level
` –15dB to 0dB to +12dB in 1 dB steps.
■ Center Level
` –12dB to 0dB
to +12dB in 1 dB steps.
Note
• You cannot use this function while the AV receiver is muted.
• Speakers that are set to “No” or “None” in the
“Speaker Configuration” (➔ 37) cannot be adjusted.
Audyssey Settings
■ Dynamic EQ
■ Dynamic Volume
See “Dynamic EQ” and “Dynamic Volume” in “Source
Setup” (➔ 41).
Late Night
With the Late Night function, you can reduce the dynamic
range of Dolby Digital material so that you can still hear
quiet parts even when listening at low volume levels—
ideal for watching movies late at night when you don’t
want to disturb anyone.
■ Late Night
For Dolby Digital and Dolby Digital Plus sources, the
options are:
` Off
:
Late Night function off.
` Low:
Small reduction in dynamic range.
` High:
Large reduction in dynamic range.
For Dolby TrueHD sources, the options are:
` Auto
:
The Late Night function is set to “On” or “Off”
automatically.
` Off:
Late Night function off.
` On:
Late Night function on.
After changing the settings of the
“HDMI Control”,
“
Audio Return Channel”, “Power Control”, or “TV Con-
trol”
, turn off the power to all connected pieces of
equipment and then turn them on again. Refer to the
user’s manuals for all connected pieces of equipment.
Lock Setup
Using the Audio Settings

Integra DTR-20.2 Specifications

General

Brand	Integra
Model	DTR-20.2
Category	Receiver
Language	English