Integra DTR-7.4 - Connecting -compatible AV Components; Connections for Remote Control ( )

26
Connecting -compatible AV Components
The terminal on the DTR-7.4 is for connecting other
Integra/Onkyo components equipped with the same
terminal. When a component is connected to the
terminal, it can be operated by the remote controller
supplied with the DTR-7.4. In addition, when you
connect a component to the
terminal, you can also
perform the system operations given below.
Power on/ready function
When the DTR-7.4 is in the standby state, if an -
connected component is turned on, the DTR-7.4 also
turns on and the input source selected at the DTR-7.4
automatically switches to that component.
Be aware that this function will not work if the power cord for the
-connected component is connected to the AC OUTLET on
the DTR-7.4, or if the DTR-7.4 has already been turned on.
Direct change function
When the play button is pressed on an
-connected
component, the input source selected at the DTR-7.4
automatically changes to that component.
Power off function
When the DTR-7.4 is placed in the standby state, all
-connected components are also automatically put
into the standby state.
Also, if you press the On button on the DTR-7.4 remote
controller while the DTR-7.4 is turned on, all -
connected components (DVD players, CD players, MD
recorders, tuners, etc.) are also turned on.
To connect components using the
terminal, simply
connect a remote control cable from this terminal to the
terminal of the other component. An remote control
cable with a 1/8 inch (3.5 mm) miniature two-conductor plug
comes with every cassette tape deck, compact disc player,
MD recorder, and DVD player that has an
terminal.
• When performing operations with -connected
components using the system, do not use the
remote zone (Zone 2).
• For remote control operation, the audio connection
cables must also be connected.
• If a component has two
terminals, you can use
either one to connect to the DTR-7.4. The other one
can be used to daisy chain with another component.
• With Integra/Onkyo DVD players, you can enter the
pre-program code so that you can operate the DVD
player directly with the remote controller without
connecting the
terminals (See page 89).
Connections for Remote Control ( )
FM
75
OUT
OUT
OUT
OUT
L
PHONO
PRE OUT
FRONT
SUB
SURR
R
L
AUDIO
R
L
CD
TAPE
R
L
AUDIO
VIDEO
S VIDEO
MONITOR
OUT
R
L
IN
IN
IN
IN
IN
IN
IN
ZONE 2
DVD
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO 4
AUDIO
AUDIO
VIDEO
S VIDEO
GND
SURR
BACK/
ZONE 2
R
L
IN
A
R
CENTER
ETHERNET
(Net -Tune)
R
L
MULTI CH
INPUT
FRONT
SUB
SURR
SURR
BACK
CENTER
R
L
ANTENNA
Y
P
B
PR
OUTPUT
INPUT 1
Y
P
B
PR
INPUT 2
Y
P
B
PR
FRONT SPEAKERS
L
RL
R
SURR SPEAKERS
CENTER
SPEAKER
R
L
IN
ZONE 2
REMOTE
CONTROL
A
B
OUT
12 V
TRIGGER OUT
DIGITAL
IN
OPT
2
1
2
3
1
3
COAX
OPT
1
2
DIGITAL
OUT
COMPONENT
VIDEO
I R
RS232
AM
REMOTE
CONTROL
L
R
ANALOG
OUTPUT
DIGITAL OUT
COAX
AUDIO
R
L
IN
DIGITAL
IN
COAX
1
REMOTE
CONTROL
Integra/Onkyo DVD player
Remote
control
cable
REMOTE
CONTROL
DTR-7.4
Ex: Integra/Onkyo CD
player
connector
connector
Ex: Onkyo cassette tape
deck
Remote control cable