Integra DTR-7.4 - Enjoying Music in the Remote Zone

68
Enjoying Music in the Remote Zone—Continued
The section explains how to turn on, select an input
source, and adjust the volume for Zone 2.
Note:
To control Zone 2 with the remote controller, you must
first press its Zone 2 button, and then press the next but-
ton within five seconds (i.e., while the DTR-7.4’s
Standby indicator is flashing).
Notes:
• If the Sleep function has been set, any Zone 2 compo-
nent will turn off along with the DTR-7.4 when the
specified sleep time expires. To use the Sleep function
with Zone 2 only, set the Sleep function and then set
the DTR-7.4 to Standby.
• Only analog input sources are output by the PRE OUT
SURR BACK/ZONE 2 outputs and the SURR BACK/
ZONE 2 SPEAKERS terminals. Digital input sources
are not output. If no sound is heard when an input
source is selected, check if it’s connected to analog
inputs.
• Since the Zone 2 function and the REC OUT outputs
use the same circuitry, if the Rec Out button is pressed,
Zone 2 will be turned off.
• When the SURR BACK/ZONE 2 outputs (SPEAK-
ERS/PRE OUT) are set to Zone 2 (page 67), listening
modes that need surround back speakers (i.e., Dolby
Digital EX, DTS-ES, and THX Surround EX) are not
available.
• While Zone 2 is active, functions will not work.
• While Zone 2 is active, the Pure Audio listening mode
cannot be selected for the main room.
• You can’t select different radio bands for Zone 2 and
the main room. For example, if you select FM for the
main room, then FM will also be selected for Zone 2.
Enjoying Music in the Remote Zone
1
Point the remote controller at the
DTR-7.4 and press the Zone 2
button followed by the On button.
This activates Zone 2 and, if connected
to the DTR-7.4’s 12V TRIGGER OUT,
turns on the Zone 2 amp.
To do this on the DTR-7.4, press
the Zone 2 button.
2
To select the Zone 2 input source
with the remote controller, press
the Zone 2 button and then roll
the scroll wheel.
The name of the selected Zone 2 source
appears on the display.
To do this on the DTR-7.4, press
the Zone 2 button, and then press
an input source button within
eight seconds.
If you select AM or FM, you can use
the remote controller’s CH/Disc +/–
button to select the presets.
To set the main room and Zone 2
sources simultaneously, press the Zone
2 button repeatedly until “Z2 Sel:
SOURCE” appears on the display.
Now use the scroll wheel or input
source buttons to select the source.
Master Volume
Tape
Tuner Phono Net AudioCD
Video 1
VCR 1
Video 3
Video 2
VCR 2
Video 4 Video 5
DVD
)
N
)
D
A
-
FO RM Listening Mode Memory
Video 5 Input
StereoDirect / Pure Audio
DSP
Surround THX
Clear
Rec Out
Zone 2 Of
f
Setup
Tuning
Preset
Enter
Return
DimmerDisplay
S Video
Audio
Video L R
Memory FM Mode
DTR
-
7.4
Digital
--
/
---
@. - ' / ABC DEF
PQRS TUV WXYZ
GHI JKL MNO
TV CH
TV VOL
RC
-
550 M
+
10 0
123
456
789
THX
DSP DSP
+
-
+
-
Direct Tuning
Caps Delete Language Loca t ion
Album Ar tist GenrePlaylist
Custom
Display
Dimmer
T V
Input
Sleep
Muting
AngleSubtitleAudio
MemorySearchA
-
BRepeat
T V
On Standby
A
u
d
i
o
A
D
J
E
x
i
t
G
u
i
d
e
Random
Step / Slow
Rec
Last Memory
Clear
Input
T
o
p
M
e
n
u
M
e
n
u
S
e
t
u
p
R
e
t
u
r
n
Zone 2
InputMode
Macro
CH
VOL
Disc
Test Tone CH SEL
Pure A
Surround
Direct
Stereo
Re
-
EQ
All CH ST
Level
+
Level
-
L Night Audio SEL
Enter
Zone 2
Level –/+
Standby
Zone 2
On
Input source
buttons
Scroll wheel
Zone 2
On
Zone 2
3
To adjust the Zone 2 volume with
the remote controller, press the
Zone 2 button, and then use the
Level –/+ buttons.
To do this on the DTR-7.4, use the
or
cursor buttons.
If your Zone 2 receiver/integrated amp
is connected to the DTR-7.4’s AUDIO
ZONE 2 OUT L/R outputs, use the vol-
ume control on the receiver/integrated
amp.
4
To turn off Zone 2 with the remote
controller, press the Zone 2 but-
ton followed by the Standby but-
ton.
To do this from the DTR-7.4,
press the Zone 2 button, and then
press the Off button within eight
seconds.
Zone 2
Level
+
Level
-
Zone 2
Standby