John Bean QUADRIGA 1000 - English; Table of Contents; List of Changement from Revision Date; Chapter: 3.1 Section: Standard Accessories

4
Operator’s Manual
Contents
QUADRIGA 1000/BB
Snap-on Equipment Srl a unico socio
Via Provinciale per Carpi, 33
42015 CORREGGIO (RE) ITALY
Tel. +39-(0)522-733480
Fax +39-(0)522-733479
E-mail: corrcs@snapon.com
Internet: http://www.gsboxer.com
Page 6
Page 12
Page 14
Page 16
Page 18
Page 18
Page 20
Page 20
Page 22
Page 26
Page 28
Page 30
Page 32
Page 32
Page 38
Page 54
Page 68
Page 70
Page 74
Page 76
Page 78
Page 82
Page 86
Page 88
Page 92
Page 96
Page 98
Page 102
Page 112
Page 112
Page 112
Page 116
Page 116
Page 120
Page 124
Page 124
All the information in this manual has been supplied
by the producer of the equipment:
TABLE OF CONTENTS
INSTRUCTION: Safety Label Meanings
1.0 Safety
1.1 Format of this Manual
1.2 Safety Devices
1.3 Machine models
1.4 Identification data
2.0 Specifications
2.1 Conditions
3.0 Introduction
3.1 Standard accessories
3.2 Accessories on request
4.0 Layout
4.1 Controls
4.1.1 User Interface
4.2 Operating Automated Parts
4.3 Operating Parts
5.0 Operations
5.1 Locking Rims
5.1.3 Clamping - Unclamping the Wheel
5.2 Demounting and Mounting tires Automatically
5.2.1 Demounting
5.2.2 Mounting
5.3 Using the Bead pusher MH
5.4 Tires beading
6.0 Maintenance
6.1 Storage
7.0 Troubleshooting
7.1 System Messages
8.0 Disposing of the unit
8.1 Instructions for disposal in EC countries
9.0 Appendices
i Installation requirements
ii Transport, Unpacking, Handling - instructions
iii Installation procedures
iv Testing procedures
v Instructing the operator
IMPORTANT!!
PLEASE READ THIS MANUAL THOROUGHLY
BEFORE USING THE MACHINE
List of changement from revision date:
A1 07/2009
Chapter: 7.1 section: Hint & Error
All languages translations completed.
List of changement from revision date:
A2 08/2009
Chapter: 3.1 section: Standard Accessories
Chapter: 3.2 section: Accessories on request
Accessories code correction.
List of changement from revision date:
B 12/2009
Chapter: 3.1 section: Standard Accessories
Accessories code correction for Kit fig. 3.1-2
Notes regarding documentation (ADDED).
List of changement from revision date:
C 04/2010
Chapter: 3.1 sect.: Standard Accessories
Accessories figure 3.1-2 - PCN 09G0243
Chap.:2.0 sect.:Specifications - PCN 10G0101
UPDATING REPORTS
List of changement from revision date:
D 05/2010
PCN: 10G0027 - 10G0107
Chapter: 3.1 sect.: Standard Accessories
Faximile EC Declaration (Added).
Chap.:2.0 sect.:Specifications
List of changement from revision date:
E 06/2010
PCN: 10G0095
Chapter: 4.1 Completed instruction on key 7
Chapter: 5.2.1 Note at pag 80, 84 (added)
Chapter: 5.4 “Beading Tires with Inner Tubes”
(removed)
Chapter: 7.1 “HINT16, HINT17” (added)
Hofmann Address on Back Cover (changed)