JUKI SC-510 Series - Simplified Program Command List

– 97 –
(4) Simplified program command list
The list below is that of command and parameter used in the simplified program function.
No. Function Abbreviation Command Output Setting Input Setting Parameter 1 Setting Parameter 2 Setting range Remarks
code setting range setting range range
10 End Completion Valid oH. 1 to 17 Invalid — Invalid — Invalid — Initial value
oL. 1 to 17
21 DELy Delay Valid oH. 1 to 17 Invalid — Invalid — Delay time (d). 0 : In case set value is “0”, command is invalid. In case of other set
oL. 1 to 17 1 to 999 X 1 mS value, step moves to next one after lapse of delay.
32 And AND conditional branch Valid oH. 1 to 17 Valid iH. 1 to 53 Skip destination No. 1 to 20 Delay time (d.) 0 : Waiting input until When all conditions designated in input setting are completed
oL. 1 to 17 iL. 1 to 53 (Sn) condition is compleed (AND input), step moves to next one.
1 to 999 X 1 mS When input conditions are not completed and delay time passed,
step jumps to that set in skip destination step No.
43 or OR conditional branch Valid oH. 1 to 17 Valid ih. 1 to 53 Skip destination No. 1 to 20 Delay time (d.) 0 : Waiting input unti When either one of conditions designated in input setting is
oL. 1 to 17 iL. 1 to 53 (Sn) condition is compleed completed (OR input), step moves to next one.
1 to 999 X 1 mS When input conditions are not completed and delay time passed,
step jumps to that set in skip destination step No.
54 STiA Number of stitches AND Valid oH. 1 to 17 Valid ih. 1 to 53 Skip destination No. 1 to 20 Number of 0 : Command invalid When all input setting conditions are completed within set value of
conditonal branch oL. 1 to 17 iL. 1 to 53 (Sn) stitches (C.) (1 to 999 stitches) number of stitches setting (ANDinput), step jumps to that
designated in skip destination step No. and moves to next step
after lapse of number of stitches.
65 STio Number of stitches OR Valid oH. 1 to 17 Valid ih. 1 to 53 Skip destination No. 1 to 20 Number of 0 : Command invalid When either one of input setting conditions is completed within set
conditonal branch oL. 1 to 17 iL. 1 to 53 (Sn) stitches (C.) (1 to 999 stitches) value of number of stitches setting, step jumps to that designated
in skip destination step No. and moves to next step after lapse of
number of stitches.
76 JUMP Jump repeat counter Valid oH. 1 to 17 Invalid Jump (Sn.) 1 to 20 Repeat vount 0 : Immense Repeat is performed between steps designated in jump until repeat
oL. 1 to 17 value (r.) (1 to 999 times) count value is over. looping is performed immensely when set value
— is “0”.
(Caution) Do not perform nest input of this command.
87 SPEd Rotation speed Valid oH. 1 to 17 Invalid Speed (S.) 0 to 999 Delay time (d.) 0 : Delay time invalid Sewing machine speed can be set. It runs at set speed within set
command oL. 1 to 17 (X 10rpm) 0 to 999 X 1mS delay time, and speed command is released after lapse of delay
time. Number of rotation at a lowest speed does not become less
— than set value of function setting No. 35 Lowest speed by pedal.
In addition, maximum speed does not become more than set value
of function setting No. 96 Maximum number of rotation.
98 LiMi Speed limitation Valid oH. 1 to 17 Invalid Speed limitation (S.) 0 to 999 Delay time (d.) 0 : Delay time invalid Maximum speed limitation value of sewing machine can be set.
command oL. 1 to 17 (X 10rpm) 0 to 999 X 1mS Set speed limitation works within set delay time and speed limitation
command is released after lapse of delay time. Number of rotation
— at slowest speed does not become less than set value of function
setting No. 35 Lowest speed by pedal. In addition, maximum speed
does not become more than set value of function setting No. 96
Maximum number of rotation.
10 9 LinH Lswinh command Valid oH. 1 to 17 Invalid on/off information on/off Delay time (d.) 0 : Wihout delay This command disables LSW (command of depressing the front part
oL. 1 to 17 (on/off) 1 to 999 X 1mS pf the panel) Command is executed without delay time with delay
— time “0”. For others, LSW is invalid within set delay time and input
of LSW is valid after setting delay time.
11 10 TrM Thread trimming Valid oH. 1 to 17 Invalid Invalid Delay time (d.) 0 : Without delay Thread trimming motion is performed.
command oL. 1 to 17 1 to 999 X 1mS Command is executed without delay time with delay time “0”. For
— others, thread trimming command is performed within set delay time.
12 11 TinH Tswinh command Valid oH. 1 to 17 Invalid on/off information on/off Delay time (d.) 0 : Without delay This command disables thread trimming output (command of
oL. 1 to 17 (on/off) 1 to 999 X 1mS depressing the back part of the pedal).
— Command is executed without delay time with delay time “0”. For
others, thread trimming delay command is performed within set
delay time and command is released after lapse of delay time.