Keithley 2002 Calibration Manual

Index
Symbols
:ACCompensation 3-13
:CALibration:PROTected subsystem 3-3
:CALibration:UNPRotected
subsystem 3-13
:DATA? 3-5
:DATE 3-5
:DC 3-6
:INIT 3-3
:LLEVel 3-11
:LOCK 3-3
:NDUE 3-5
:SAVE 3-4
:SWITCH 3-4
Numerics
1GΩ range verification 1-15
20MΩ and 200MΩ range verification 1-14
20Ω-2M range verification 1-13
A
AC current verification 1-12
AC peak mode 1-10
AC self-calibration 2-12
AC volts verification 1-6
Additional derating factors 1-2
B
BASIC program requirements B-1
Bus error reporting 3-13
C
Calibration 2-1
Calibration command reference 3-1
Calibration command summary D-1
Calibration data query response C-1
Calibration equipment B-1
Calibration error summary 3-13
Calibration errors 2-4
Calibration lock 2-2
Calibration messages C-1
Calibration programs B-1
Command summary 3-1
Commands 3-1
Comprehensive calibration 2-4, B-3
Comprehensive calibration lock 2-2
Computer hardware requirements B-1
D
DC current verification 1-11
DC volts verification 1-4
Detecting calibration errors 3-13
Detecting calibration step completion 3-14
E
Environmental conditions 1-1, 2-2
Error generation C-1
Error summary C-1
Error queue 3-13
F
Frequency accuracy verification 1-15
Front panel AC calibration 2-12
Front panel comprehensive calibration 2-4
Front panel error reporting 2-4
Front panel low-level calibration
procedure 2-16
Front panel single-point calibration 2-24
G
General program instructions B-3
Generating an SRQ on calibration
complete 3-14
Generating an SRQ on error 3-13
I
IEEE-488 bus AC self-calibration 2-13
IEEE-488 bus calibration commands 2-2
IEEE-488 bus calibration lock status 2-2
IEEE-488 bus comprehensive calibration 2-9
IEEE-488 bus error reporting 2-4
IEEE-488 bus low-level calibration
procedure 2-20
IEEE-488 bus single-point calibration 2-24
Introduction 1-1, 2-1, 3-1, B-1, C-1
Invalid calibration data error C-1
L
Line power 1-2, 2-2
Low-frequency mode 1-9
Low-level calibration 2-13, B-3
Low-level calibration lock 2-2
Low-level calibration summary 2-13
N
Normal mode 1-6
P
Performance verification 1-1
R
Recommended equipment for
comprehensive calibration 2-4
Recommended equipment for low-level
calibration 2-13
Recommended test equipment 1-2
Reading limit calculation example 1-2
Resistance verification 1-13
Restoring default conditions 1-2
RTD temperature reading checks 1-18
i-1

Keithley 2002 Specifications

General

Resolution	8.5 digits
DC Voltage Accuracy	±0.0006%
Maximum DC Voltage	1000 V
Maximum AC Voltage	750 V
Maximum DC Current	3 A
Maximum AC Current	3 A
Connectivity	GPIB, RS-232
DC Voltage Range	100 mV to 1000 V
AC Voltage Range	100 mV to 750 V
Resistance Range	10 Ω to 1 GΩ
Model	2002
Category	Multimeter
Interface	GPIB, RS-232
AC Current Accuracy	±0.1%
Frequency Range	0.1Hz to 300kHz
Display	VFD
Type	Digital
Power Supply	100-240V AC, 50/60Hz
Current Range (DC)	100 μA to 3 A
Current Accuracy (DC)	±0.01%
Current Range (AC)	100 μA to 3 A
Current Accuracy (AC)	±0.1%
DC Current Range	100 μA to 3 A
AC Current Range	100 μA to 3 A