Kimo KIGAS 310 - User Manual

To Next Page

Main Page

Table of Contents3
Introduction7
- Description of the Analyser7
- Main Features9
- Technical Features11
Safety12
- Precautions for Use12
- Symbols Used12
- Safety Instructions12
Perform a Flue Gas Analysis13
- Prepare the Instrument before the Analysis13
- Perform an Analysis13
- Zoom Function14
- Assign the Analysis to a Customer14
- Add the Measurement to a Group14
- Print the Analysis Results14
Perform a Quick Measurement15
Set the Different Parameters of the Analyser16
- Instrument Setting16
- Set the Combustible18
- Set the Alarms, Measurement Units and CO Protection19
- Set the References20
- Set the Auto-Zero and Purge Time20
- Set the Operators20
- Back to Factory Setting of the Analyser21
  - Units and Values of Measurement Settings of the Factory Setting21
  - Device Factory Setting21
Manage Customers22
- Create a Customer22
- Modify a Customer22
- Delete a Customer22
Manage Boilers23
- Create a Boiler23
- Modify a Boiler23
- Delete a Boiler23
Manage the Inspections24
- Get to Inspections24
- Create an Inspection24
- Delete an Inspection24
- Create a Group24
- Add an Inspection to a Group25
- Delete a Group25
Perform Measurement of a Customised Procedure25
- Preliminary Operations to Procedures25
- Launch a Customised Procedure25
Perform a Control of Gas Flow26
- Perform a Measurement of Theoretical Flow26
- Perform a Measurement of Real Flow26
- Results Interpretation26
Perform a Gas Network Leak Test27
- Perform the Test27
- Link the Measurement to a Customer27
- Print the Results27
Perform a Pressure Measurement28
- Perform a Draft Measurement28
- Perform a Differential Pressure Measurement28
- Perform a Flue Gas Velocity Measurement28
- Link the Measurement to a Customer28
- Add the Measurement to a Group28
- Print the Results28
Perform a Measurement of Ambient CO29
- Perform the Measurement29
- Link the Measurement to a Customer29
- Add the Measurement to a Group29
- Print the Results29
Perform a Measurement of Max CO30
- Perform the Measurement30
- Link the Measurement to a Customer30
- Add the Measurement to a Group30
- Print the Results30
Perform some Temperature Measurements31
- Perform a Measurement of Ambient Temperature31
- Perform a Measurement of Flue Gas Temperature31
- Perform an Ambient Temperature Measurement with the Internal Sensor31
- Perform a Flow/Return Temperature Measurement31
- Link the Measurement to a Customer31
- Add the Measurement to a Group31
- Print the Results31
Perform a Measurement of Opacity32
- Perform the Measurement32
- Enter the Indexes in the Analyser32
- Link the Measurement to a Customer32
- Add the Measurement to a Group32
- Print the Results32
Perform a Measurement of Ionisation Current33
- Perform the Measurement33
- Link the Measurement to a Customer33
- Add the Measurement to a Group33
- Print the Results33
Perform a CH Measurement34
- Perform the Measurement with the Probe34
- Perform the Measurement with the Sensor34
- Link the Measurement to a Customer34
- Add the Measurement to a Group34
- Print the Results34
Perform a Flue Gas Velocity Measurement with a Pitot Tube35
- Link the Measurement to a Customer35
- Add the Measurement to a Group35
- Print the Results35
To Get to Information about the Analyser36
- Information36
- Diagnostics36
  - Air Flow36
  - Gas Leak Test37
Maintenance of the Analyser38
- Life-Time of the Sensors38
- Replace the Paper Roll of the Printer40
- Replace the Battery40
Calculations of the Different Parameters41
- CO, no and Nox Conversions41
- Calculation of the Level in Nox41
- Calculation of Flue Gas Velocity41
Introduction44
Software Installation44
- Recommended Minimum Configuration44
- Installation44
Start with the Software45
- Meaning and Functions of the Menus Bar (1)45
- Meaning and Functions of Tool Bar Buttons (2)46
- Meaning and Functions of the Homepage Buttons (3)46
Download Inspections46
Use the Different Databases47
- Use the Customer Database47
- Use the Boilers Database48
- Complete Database50
- Edit an Analysis Report51
Set the Analyser52
- Change the Combustibles52
- Change the References52
- Manage the Operators52
- Modify the Date and Time53
- Sensors State53
- Set Printings53
- Battery Level53
- Access to Information about the Instrument and Update the Instrument53
Options55
- E-Mail55
- User Information55
- Change the Language55
Customers / Boilers Deletion of the Analyser56
Compare the Instrument and Software Information57
- Add Elements Automatically in the Databases57
- Modification of Customer and Boilers Features57

Brand	Kimo
Model	KIGAS 310
Category	Measuring Instruments
Language	English

Kimo KIGAS 310 - User Manual

Table of Contents

Kimo KIGAS 310 Specifications

Related product manuals