Kimo KIGAS 310 - Page 42

60 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

42 Calculations of the different parameters

Table of Contents

Table of Contents3
Introduction7
- Description of the Analyser7
- Main Features9
- Technical Features11
Safety12
- Precautions for Use12
- Symbols Used12
- Safety Instructions12
Perform a Flue Gas Analysis13
- Prepare the Instrument before the Analysis13
- Perform an Analysis13
- Zoom Function14
- Assign the Analysis to a Customer14
- Add the Measurement to a Group14
- Print the Analysis Results14
Perform a Quick Measurement15
Set the Different Parameters of the Analyser16
- Instrument Setting16
- Set the Combustible18
- Set the Alarms, Measurement Units and CO Protection19
- Set the References20
- Set the Auto-Zero and Purge Time20
- Set the Operators20
- Back to Factory Setting of the Analyser21
  - Units and Values of Measurement Settings of the Factory Setting21
  - Device Factory Setting21
Manage Customers22
- Create a Customer22
- Modify a Customer22
- Delete a Customer22
Manage Boilers23
- Create a Boiler23
- Modify a Boiler23
- Delete a Boiler23
Manage the Inspections24
- Get to Inspections24
- Create an Inspection24
- Delete an Inspection24
- Create a Group24
- Add an Inspection to a Group25
- Delete a Group25
Perform Measurement of a Customised Procedure25
- Preliminary Operations to Procedures25
- Launch a Customised Procedure25
Perform a Control of Gas Flow26
- Perform a Measurement of Theoretical Flow26
- Perform a Measurement of Real Flow26
- Results Interpretation26
Perform a Gas Network Leak Test27
- Perform the Test27
- Link the Measurement to a Customer27
- Print the Results27
Perform a Pressure Measurement28
- Perform a Draft Measurement28
- Perform a Differential Pressure Measurement28
- Perform a Flue Gas Velocity Measurement28
- Link the Measurement to a Customer28
- Add the Measurement to a Group28
- Print the Results28
Perform a Measurement of Ambient CO29
- Perform the Measurement29
- Link the Measurement to a Customer29
- Add the Measurement to a Group29
- Print the Results29
Perform a Measurement of Max CO30
- Perform the Measurement30
- Link the Measurement to a Customer30
- Add the Measurement to a Group30
- Print the Results30
Perform some Temperature Measurements31
- Perform a Measurement of Ambient Temperature31
- Perform a Measurement of Flue Gas Temperature31
- Perform an Ambient Temperature Measurement with the Internal Sensor31
- Perform a Flow/Return Temperature Measurement31
- Link the Measurement to a Customer31
- Add the Measurement to a Group31
- Print the Results31
Perform a Measurement of Opacity32
- Perform the Measurement32
- Enter the Indexes in the Analyser32
- Link the Measurement to a Customer32
- Add the Measurement to a Group32
- Print the Results32
Perform a Measurement of Ionisation Current33
- Perform the Measurement33
- Link the Measurement to a Customer33
- Add the Measurement to a Group33
- Print the Results33
Perform a CH Measurement34
- Perform the Measurement with the Probe34
- Perform the Measurement with the Sensor34
- Link the Measurement to a Customer34
- Add the Measurement to a Group34
- Print the Results34
Perform a Flue Gas Velocity Measurement with a Pitot Tube35
- Link the Measurement to a Customer35
- Add the Measurement to a Group35
- Print the Results35
To Get to Information about the Analyser36
- Information36
- Diagnostics36
  - Air Flow36
  - Gas Leak Test37
Maintenance of the Analyser38
- Life-Time of the Sensors38
- Replace the Paper Roll of the Printer40
- Replace the Battery40
Calculations of the Different Parameters41
- CO, no and Nox Conversions41
- Calculation of the Level in Nox41
- Calculation of Flue Gas Velocity41
Introduction44
Software Installation44
- Recommended Minimum Configuration44
- Installation44
Start with the Software45
- Meaning and Functions of the Menus Bar (1)45
- Meaning and Functions of Tool Bar Buttons (2)46
- Meaning and Functions of the Homepage Buttons (3)46
Download Inspections46
Use the Different Databases47
- Use the Customer Database47
- Use the Boilers Database48
- Complete Database50
- Edit an Analysis Report51
Set the Analyser52
- Change the Combustibles52
- Change the References52
- Manage the Operators52
- Modify the Date and Time53
- Sensors State53
- Set Printings53
- Battery Level53
- Access to Information about the Instrument and Update the Instrument53
Options55
- E-Mail55
- User Information55
- Change the Language55
Customers / Boilers Deletion of the Analyser56
Compare the Instrument and Software Information57
- Add Elements Automatically in the Databases57
- Modification of Customer and Boilers Features57

Related product manuals

Preview: Kimo KIGAZ 210

Preview: Kimo TH210

Preview: Kimo HD110

Preview: Kimo VT110

Preview: Kimo mp210

Preview: Kimo DB 200

Preview: Kimo CO 110

Preview: Kimo MP 100

Preview: Kimo MP 120

Preview: Kimo DBM610

Preview: Kimo DB300/1

Preview: Kimo MP Series