EasyManua.ls Logo

KITO CX005 - User Manual

KITO CX005
44 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
This equipment should not be installed,operated or
maintained by any person who has not read and
understood all the contents of this manual. Failure to
read and comply with the contents of this manual can
result in serious bodily injury or death, and/or property
damage.
Issued August, 2011. Revised November, 2019 (Revision 05)
OM-CX1ZZZ-CEE-02
/005
Original Instruction

Table of Contents

Questions and Answers

  • T
    Tara WoodAug 19, 2025
    What to do if my KITO Chain Hoists lifting up failure?
    • M
      Mark KeyAug 19, 2025
      If your KITO Chain Hoists fails to lift up, several issues could be the cause. Check the following: * Ensure the Ratchet Disc and Pawl are correctly engaged by reassembling them. * Verify the Pawl is not upside down; reassemble it in the correct direction. * Clean any dust or rust from the Pawl Shaft and Pawl to ensure good contact with the Ratchet Disc. If rust is significant, replace the parts. * Confirm the 'O' and 'V' marks on Gear #2 are correctly aligned during reassembly and perform an operational test. * Make sure the Load Chain isn't twisted or tangled between the Chain Guide and Load Sheave; reassemble it carefully. * If the Overload Limiter (OLL) is faulty due to frequent overloading, stop using the hoist and replace the Hand Wheel Assembly.
  • Q
    qharperAug 21, 2025
    Why does the hand chain slip on my KITO CX005 Chain Hoists?
    • R
      Richard NelsonAug 21, 2025
      If the hand chain on your KITO Chain Hoists is slipping, it could be due to several reasons: * The sprocket of the Hand Wheel may be worn; consider replacing the Hand Wheel Assembly. * The Hand Chain may be elongated or worn; use a proper Hand Chain. * The Hand Chain might be the wrong size; ensure you are using the correct Hand Chain.
  • H
    Heather CochranAug 23, 2025
    What to do if KITO Chain Hoists load drifts?
    • C
      clarkjasonAug 23, 2025
      If the load drifts when using your KITO Chain Hoists, it may be caused by: * Slight dust on the brake surface. In this case, disassemble the Chain Hoist, remove the dust, and then reassemble it. * Oil, such as grease, attached to the brake surface. Disassemble the Chain Hoist, remove the oil, and then reassemble.
  • A
    Adrienne BrownAug 26, 2025
    Why is there rust or corrosion on my KITO CX005?
    • K
      Kristin GuzmanAug 26, 2025
      Rust or corrosion on your KITO Chain Hoists can occur due to: * Lack of oil. Remove any dirt and water, and then apply oil to the neck of the Hook and Load Chains. * Exposure to rain. Store the Chain Hoist indoors. * Influence from seawater, chemicals, etc. Ensure thorough safety control in accordance with the operating environment.
  • R
    rjohnsonAug 28, 2025
    What to do if KITO CX005 load falls when lowering starts?
    • J
      Jesse DavilaAug 28, 2025
      If the load falls when you start lowering it with your KITO Chain Hoists, it could be because: * There is a foreign object between friction surfaces. Disassemble the Chain Hoist, remove the object, and then reassemble. * Brake slip is caused by significant rust. Reassemble the rusted part.
  • S
    salinastimothyAug 30, 2025
    Why is it hard to lower load with KITO Chain Hoists?
    • K
      Kaitlyn BrooksAug 30, 2025
      If it's hard to lower a load with your KITO Chain Hoists, it may be because the Caw Guide contacts the inner upper right corner of the Hand Wheel. Reassemble it.
  • S
    Sarah JonesSep 1, 2025
    What to do if my KITO CX005 Chain Hoists hook is stretched?
    • J
      John BurnsSep 2, 2025
      If the hook on your KITO Chain Hoists is stretched, it's likely due to: * Overload. The Hook is designed to open gradually under more than double the rated load. Replace the Hook. * Lifting a load at the tip of the Hook. Replace the Hook. * Improper hooking of the sling or using a sling of inappropriate size relative to the Hook. Replace the Hook.
  • B
    Brittany DavisSep 3, 2025
    What to do if my KITO CX005 Chain Hoists is not lowering load?
    • J
      Jason GlassSep 4, 2025
      If your KITO Chain Hoists is not lowering the load, it may be because: * Leaving the Chain Hoist loaded for a long time or subjecting it to mechanical impact during work may lock the brake. Try pulling the Hand Chain strongly for lowering for a moment to release the brake. * Rust locks the brake. Replace the rusted part.
  • S
    shane17Sep 6, 2025
    Why is the hook neck bent on my KITO Chain Hoists?
    • A
      Alec BarnesSep 6, 2025
      If the hook neck on your KITO Chain Hoists is bent, it could be due to: * Lifting a load at the tip of the Hook. Replace the Hook. * Applied force from an oblique direction to the Hook being fixed. Replace the Hook.
  • G
    Gloria JohnstonSep 8, 2025
    Why is the hook twisted on my KITO Chain Hoists?
    • Y
      ydixonSep 9, 2025
      If the hook on your KITO Chain Hoists is twisted, it's likely because the Load Chain was wound around the load. Replace the Hook.

Summary

Safety Precautions

Signal Word Definitions

Defines hazard symbols like Danger, Warning, and Caution for safety.

Usage Restrictions

Specifies prohibited uses, such as transporting people.

Chapter 1: Operation

Operation Safety Guidelines

Essential safety rules for operating the chain hoist correctly.

Technical Specifications

Key performance data and dimensions for CX003/005 models.

Installation and Pre-operation

Steps for mounting, setup, and pre-use checks.

Operation Method

Proper techniques for lifting and lowering loads.

Daily Inspection

Routine checks by operator before daily use.

Chapter 2: Inspection

Inspection Safety Precautions

Safety rules for performing inspections on the hoist.

Inspection Standards

Criteria for assessing component condition and wear limits.

Frequent Inspection

Detailed checks for regular intervals.

Periodic Inspection

In-depth checks requiring disassembly and reassembly.

Chapter 3: Troubleshooting

Troubleshooting Safety

Safety measures during repair and maintenance activities.

Lifting Up Failures

Diagnosis and solutions for problems with lifting loads.

Lowering Failures

Diagnosis and solutions for problems with lowering loads.

Warranty Information

Warranty Details

Explains warranty coverage, terms, and conditions.

KITO CX005 Specifications

General IconGeneral
BrandKITO
ModelCX005
CategoryChain Hoists
LanguageEnglish

Related product manuals