EasyManua.ls Logo

KITO EQ series - User Manual

KITO EQ series
126 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
OM-EQ1ZZZ-MGE-00
To Customer
7KDQN\RXIRUSXUFKDVLQJ.,72(OHFWULF+RLVW(4
2SHUDWRUVDQGPDLQWHQDQFHHQJLQHHUVDUHUHTXHVWHGWRUHDGWKLVPDQXDO
$IWHUUHDGLQJSOHDVHNHHSWKLVPDQXDODWKDQGIRUIXWXUHXVH
7KLV SURGXFW LV GHVLJQHG FRQVLGHULQJ WKH HQYLURQPHQW SURWHFWLRQ 7KH SURGXFW FRQWDLQV QRQH RI VL[ KD]DUGRXV
VXEVWDQFHVVSHFLILHGE\(XURSHDQ5R+6'LUHFWLYHVQRUDVEHVWRV
Suspended Type (hoist only) : EQ
Motorized Trolley Type : EQM
Manual Trolley Type : EQSP/EQSG
EQ Series Electric Chain Hoist
(125kg to 1t)
Owner's Manual

Table of Contents

Other manuals for KITO EQ series

Preview: Assembly/Disassembly Manual
Assembly/Disassembly Manual26 pages

Questions and Answers

  • K
    kstephensAug 20, 2025
    What to do if my KITO EQ Chain Hoists electric chain hoist does not operate without load?
    • S
      Shannon HenryAug 20, 2025
      If your KITO Chain Hoists electric chain hoist isn't working without a load, it could be due to several reasons: * Improper source voltage, so check the power. * Breakage and burning of the control circuit, so check the circuit breaker, power cable, internal wiring, HBB Board, VFD, or upper/lower limit switch. * Breakage and burning of the power circuit, so check the motor or internal wiring. * VFD trip due to motor overheat (electronic thermal relay), so check the VFD. * VFD overheat, so check the VFD.
  • J
    Juan ObrienAug 22, 2025
    Why does my KITO EQ electric chain hoist operate without load?
    • Y
      Yesenia CampbellAug 22, 2025
      If your KITO Chain Hoists electric chain hoist is operating without a load, the causes could be: * Overload (Clutch activated), so check the friction clutch. * Voltage drop, so check the power cable. * Low source voltage, so check the power. * Faulty braking resistor, so check the braking resistor.
  • S
    Suzanne RoseAug 25, 2025
    What to do if my KITO Chain Hoists does not stop normally?
    • R
      Ryan DeanAug 25, 2025
      If your KITO Chain Hoists does not stop normally, it could be due to: * Abrasion of brake lining, so check the brake. * Negative phase connection of motor lead wires, so check the power cable. * Wrong connection, so check the internal wiring. * Push Button Switch.
  • R
    Rachel KruegerAug 26, 2025
    What to do if KITO Chain Hoists operates differently from the indication of the Push Button Switch?
    • C
      copelandraymondAug 26, 2025
      If your KITO Chain Hoists operates differently from the indication of the Push Button Switch, the issue might stem from: * Negative phase connection of motor lead wires, so check the motor. * Wrong connection, so check the internal wiring. * Push Button Switch. * Breakage of control circuit, so check the internal wiring or push button switch. * Faulty electrical part, so check the VFD, HBB Board, or Upper/Lower Limit Switch.
  • A
    Amber DavisAug 28, 2025
    Why KITO Chain Hoists makes an abnormal noise?
    • J
      Jennifer GreeneAug 28, 2025
      Abnormal noise in your KITO Chain Hoists may be caused by: * Abrasion of the Load Chain, so check the load chain. * Abrasion of the Load Sheave, so check the load sheave. * Abrasion or breakage of Gear, so check the gears. * Deterioration of Bearing, so check the bearing. * Dragging, so check the brake. * Abrasion of brake lining, so check the brake.
  • A
    Amanda SchmidtAug 29, 2025
    Why am I getting an electric shock from my KITO EQ?
    • P
      Patricia AndersonAug 29, 2025
      If you experience an electric shock when touching the body or the Push Button Switch of your KITO Chain Hoists, it's likely due to improper grounding or a broken earth wire. To resolve this, ensure the grounding work is performed securely.
  • B
    bradley32Aug 31, 2025
    What to do if my KITO electric chain hoist does not operate?
    • A
      adam86Aug 31, 2025
      If your KITO electric chain hoist isn't operating, begin by measuring the voltage of each phase at the power receiving terminal. If the source voltage is incorrect, inspect the power receiving facility to ensure it is providing the correct voltage.
  • C
    Charles WarrenSep 2, 2025
    Why motor does not operate on KITO Chain Hoists?
    • K
      Kathleen JohnsonSep 2, 2025
      If the motor of your KITO Chain Hoists isn't operating, it could be due to: * Motor coil burning (two or more phases). * Lead wire breakage (more than two lead wires). If the resistance of all phases is infinite, replace the motor.
  • D
    Dustin CastilloSep 4, 2025
    What to do if KITO electric chain hoist does not stop normally?
    • K
      kendra61Sep 4, 2025
      If your KITO electric chain hoist does not stop normally, it could be due to abrasion of the brake lining. Check the manner of operation (excessive inching or frequent use) and carry out the inspection and use it correctly.
  • D
    Douglas CortezSep 6, 2025
    Why breaker was tripped due to short circuit on KITO EQ?
    • C
      Crystal WoodSep 6, 2025
      If the breaker trips due to a short circuit in your KITO Chain Hoists, it could be due to cable breakage or burning of electrical parts. Please refer to each item of Power Cable, Motor and Internal Wiring.

Summary

Chapter 1: Handling the Product

Product Specification and Operational Environment

Outlines technical specifications, ratings, protection, and power supply for EQ series hoists.

How to Use

General guidelines and specific instructions for operating the electric chain hoist safely.

Daily Inspection of Electric Chain Hoist (EQ)

Procedures for daily checks of the electric chain hoist's appearance and function.

Operation and Safety Guidelines

General guidelines and specific instructions for operating the electric chain hoist safely.

Lifting;Lowering Procedures

Detailed safety precautions and procedures for lifting and lowering loads with the hoist.

Work Flow of Assembling and Installation

Overview of the step-by-step process for assembling and installing the hoist and trolleys.

Assembling

Instructions for assembling the electric chain hoist and its components.

Combination with the Trolley

Guidance on combining the hoist with different types of trolleys.

Spacer Adjustment for Motorized Trolley

Details on selecting and positioning spacers for motorized trolley installation.

Spacer Adjustment for Manual Trolley

Combination of Electric Chain Hoist and Motorized Trolley

Combination of Electric Chain Hoist and Manual Trolley

Checking Power and Power Cable

Connecting Cables

Installation

Installing the Suspended Type (hoist only)

Installing the Trolley Combined Model

Check after Installation

Chapter 2: Inspection

Safety Precautions for Inspection

Essential safety rules and precautions to follow during inspection procedures.

Frequent Inspection Procedures

Periodic Inspection Procedures

Check of Operating Hours and Number of Start (CH Meter)

Chapter 3: Troubleshooting

Guidance on Troubleshooting

Table summarizing common faults, causes, check items, and reference pages for troubleshooting.

Safety Precautions for Troubleshooting

General safety rules for repair, maintenance, and handling of the hoist during troubleshooting.

Troubleshooting Specific Components

Diagnosing and resolving issues related to power, motor, brake, and electrical components.

Power and Circuit Breaker Issues

Motor and Brake Problems

Limit Switch and Push Button Issues

Load Chain and Hook Issues

Traveling motion of the Trolley

KITO EQ series Specifications

General IconGeneral
BrandKITO
ModelEQ series
CategoryChain Hoists
LanguageEnglish

Related product manuals