189
019: Ensemble
This Ensemble effect has three chorus blocks that use
LFO to create subtle shimmering, and gives three
dimensional depth and spread to the sound, because
the signal is output from the left, right, and center.
c: Shimmer
This parameter sets the amount of shimmering of the LFO
waveform. Increasing this value adds more shimmering, mak-
ing the chorus effect more complex and richer.
020: Flanger
(Stereo Flanger)
This effect gives a significant swell and movement of
pitch to the sound. It is more effective when applied to
a sound with a lot of harmonics. This is a stereo flanger.
You can add spread to the sound by offsetting the
phase of the left and right LFOs from each other.
b: LFO Shape
Changing the LFO waveform shape controls the peak sweep
of flanging effects.
g: Feedback, h: Wet/Dry
The peak shape of the positive and negative “Feedback”
value is different. The harmonics will be emphasized when
the effect sound is mixed with the dry sound if you set a posi-
a
Speed
Sets the LFO speed
1...100
Src
Selects the modulation source of LFO speed
Off...Tempo
Amt
Sets the modulation amount of LFO speed
–100...+100
b
Depth
Sets the depth of LFO modulation
0...100
Src Off...Tempo
Selects the modulation source of the LFO modulation depth
Amt –100...+100
Sets the modulation amount of the LFO modulation depth
c
Shimmer 0...100
Sets the amount of shimmering of the LFO waveform →
d
Wet/Dry Dry, 1:99...99:1, Wet
Table , “Sets the balance between the effect and dry sounds,” on page 177
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 177
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 177
–100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
LFO
Shimmer
+
Ensemble
Time
Level
Ensemble LFO
Shimmer
a
Delay Time [msec]
Sets the delay time from the original sound
0.0...50.0msec
b
LFO Waveform
Selects LFO Waveform
Triangle, Sine
LFO Shape –100...+100
Determines how much the LFO waveform is changed →
c
LFO Phase [degree] –180...+180
Sets the LFO phase difference between the left and right →Fx:010
d
LFO Frequency [Hz] 0.02...20.00Hz
Sets the LFO speed →Fx:009,
Src
Selects the modulation source of LFO speed
Off...Tempo
Amt –20.00...+20.00Hz
Sets the modulation amount of LFO speed
e
BPM/MIDI Sync Off, On
Switches between using the frequency of the LFO speed and using the
tempo and notes →Fx:009,
BPM
Selects MIDI Clock and assigns tempo
MIDI, 40...240
→Fx:009
Base Note
Selects the type of notes that specify the LFO speed →Fx:009
Times x1...x16
Sets the number of notes that specify the LFO speed →Fx:009
f
Depth
Sets the depth of LFO modulation
0...100
g
Feedback
Sets the feedback amount
–100...+100
→
High Damp [%] 0...100%
Sets the feedback damping amount in the high range →
h
Wet/Dry –Wet...–1:99, Dry, 1:99...Wet
Table , “Sets the balance between the effect and dry sounds,” on page 177
→Fx:010,
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 177
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 177
–100...+100
Flanger
Flanger
Left
Right
Feedback
LFO Shape
LFO Phase
LFO: Tri / Sine
Wet / Dry
Wet / Dry
High Damp
Stereo In - Stereo Out
LFO Shape
LFO Shape = 0...+100
LFO Shape = 0...–100
LFO Waveform=Sine
To Next Page
Loading...
