190
tive value for both “Feedback” and “Wet/Dry”, and if you set a
negative value for both “Feedback” and “Wet/Dry”.
g: High Damp [%]
This parameter sets the amount of damping of the feedback
in the high range. Increasing the value will cut high-range har-
monics.
021: RandomFlang
(Stereo Random Flanger)
The stereo effect uses a step-shape waveform and ran-
dom LFO for modulation, creating a unique flanging
effect.
022: Envel.Flang
(Stereo Envelope Flanger)
This Flanger uses an envelope generator for modula-
tion. You will obtain the same pattern of flanging each
time you play. You can also control the Flanger directly
using the modulation source.
c: Sweep Mode, c: Src
This parameter switches the flanger control mode. With
“Sweep Mode” = EG, the flanger will sweep using the enve-
lope generator. This envelope generator is included in the
envelope flanger, and not related to the Pitch EG, Filter EG, or
Amp EG.
The “Src” parameter selects the source that starts the enve-
lope generator. If you select, for example, Gate, the envelope
generator will start when the note-on message is received.
When “Sweep Mode” = D-mod, the modulation source can
control the flanger directly. Select the modulation source
using the “Src” parameter.
The effect is off when a value for the modulation source specified for
the “Src” parameter is smaller than 64, and the effect is on when the
value is 64 or higher. The Envelope Generator is triggered when the
value changes from 63 or smaller to 64 or higher.
d: EG Attack, d: EG Decay
Attack and Decay speed are the only adjustable parameters
on this EG.
a
Delay Time [msec]
Sets the delay time from the original sound
0.0...50.0msec
b
LFO Waveform
Selects LFO Waveform
Step-Tri, Random
→Fx:010
c
LFO Phase [degree] –180...+180
Sets the LFO phase difference between the left and right →Fx:010
d
LFO Frequency [Hz] 0.02...20.00Hz
Sets the LFO speed →Fx:010,
Src Off...Tempo
Selects the modulation source used for both LFO speed and step speed
Amt –20.00...+20.00Hz
Sets the modulation amount of LFO speed
e
LFO Step Freq (Frequency) [Hz] 0.05...50.00Hz
Sets the LFO step speed (speed that changes in steps)
→Fx:010,
Amt –50.00...+50.00Hz
Sets the modulation amount of LFO step speed
f
BPM/MIDI Sync Off, On
Switches between using the frequency of the LFO speed and using the
tempo and notes →Fx:009,
BPM
Selects MIDI Clock and assigns tempo
MIDI, 40...240
→Fx:009, 010
Base Note
Selects the type of notes that specify the LFO speed →Fx:009
Times x1...x16
Sets the number of notes that specify the LFO speed →Fx:009
g
Step Base Note
Selects the type of notes to specify the LFO step speed
→Fx:010,
Times x1...x32
Sets the number of notes to specify the LFO step speed →Fx:010
h
Depth
Sets the depth of LFO modulation
0...100
i
Feedback
Sets the feedback amount
–100...+100
→Fx:020
High Damp [%] 0...100%
Sets the feedback damping amount in the high range →Fx:020
j
Wet/Dry –Wet...–1:99, Dry, 1:99...Wet
Table , “Sets the balance between the effect and dry sounds,” on page 177
→Fx:010, 020,
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 177
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 177
–100...+100
LFO: Step-Tri/Random
Left
Right
Feedback
LFO Phase
Wet / Dry
Wet / Dry
High Damp
Stereo In - Stereo Out
Flanger
Flanger
a
L Dly Bottom [msec] (L Delay Bottom) 0.0...50.0msec
Sets the lower limit of the delay time on the left channel →Fx:009
L Dly Top [msec] (L Delay Top) 0.0...50.0msec
Sets the upper limit of the delay time on the left channel →Fx:009
b
R Dly Bottom [msec] (R Delay Bottom) 0.0...50.0msec
Sets the lower limit of the delay time on the right channel →Fx:009
R Dly Top [msec] (R Delay Top) 0.0...50.0msec
Sets the upper limit of the delay time on the right channel →Fx:009
c
Sweep Mode EG, D-mod
Determines whether the flanger is controlled by the envelope generator or by
the modulation source →,
Src Off...Tempo
Selects the modulation source that triggers the EG (when EG is selected for
Sweep Mode), or modulation source that causes the flanger to sweep (when
D-mod is selected for Sweep Mode) →
d
EG Attack
Sets the EG attack speed
1...100
→
EG Decay
Sets the EG decay speed
1...100
→
e
Feedback
Sets the feedback amount
–100...+100
→Fx:020
f
High Damp [%] 0...100%
Sets the feedback damping amount in the high range →Fx:020
g
Wet/Dry –Wet...–1:99, Dry, 1:99...Wet
Table , “Sets the balance between the effect and dry sounds,” on page 177
→Fx:010, 020,
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 177
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 177
–100...+100
EG Attack/Decay
EG
D-mod
Sweep Mode
D
-mod
Flanger
Flanger
Left
Right
Feedback
Wet / Dry
Wet / Dry
High Damp
Stereo In - Stereo Out
To Next Page
Loading...
