Kramer VW-16 - Page 54

Kramer Electronics Ltd.
VW-16 – Protocol 3000
52
Function
Description
Syntax
Parameters/
Attributes
Example
103=Custom resolution 4
104=Custom resolution 5
104-254=(Reserved)
VIEW-MOD
Set view mode.
COMMAND
#VIEW-MODmode<CR>
FEEDBACK
~nn@VIEW-MODmode<CR><LF>
mode – View Modes
0 – PIP off (matrix)
1 – PIP on (dual PIP)
2 – Preview (not applicable)
3 – Quad
4 – Video wall
5 – POP
Set view mode:
#VIEW-MOD1<CR>
VIEW-MOD?
Get view mode.
COMMAND
#VIEW-MOD?<CR>
FEEDBACK
~nn@VIEW-MODmode<CR><LF>
mode – View Modes
0 – PIP off (matrix)
1 – PIP on (dual PIP)
2 – Preview (not applicable)
3 – Quad
4 – Video wall
5 – POP
Get view mode:
#VIEW-MOD?<CR>
VMUTE
Set enable/disable video
on output.
COMMAND
#VMUTEout_index,flag<CR>
FEEDBACK
~nn@VMUTEout_index,flag<CR><LF>
out_index – Number that indicates the
specific output:
1-N (N= the total number of outputs)
flag – Video Mute
0 – Video enabled
1 – Video disabled
2 – Blank picture
Disable the video output
on OUT 2:
#VMUTE2,0<CR>
VMUTE?
Get video on output
status.
COMMAND
#VMUTE?out_index<CR>
FEEDBACK
~nn@VMUTEout_index,flag<CR><LF>
out_index – Number that indicates the
specific output:
1-N (N= the total number of outputs)
flag – Video Mute
0 – Video enabled
1 – Video disabled
2 – Blank picture
Get video on output
status:
#VMUTE?2<CR>
W-BRD
Enable/disable window
border.
COMMAND
#W-BRDwin_number,enable<CR>
FEEDBACK
~nn@W-BRDwin_number,enable<CR><LF>
win_num – Window number to
enable/disable
enable – 1, disable 0
Enable/disable window
border :
#VMUTE1,1<CR>
W-BRD?
Get window border status.
COMMAND
#W-BRD?win_num<CR>
FEEDBACK
~nn@W-BRDwin_num,enable<CR><LF>
win_num – Window number to
enable/disable
enable – 1, disable 0
Get window border
status:
#VMUTE1<CR>
W-HUE
Set window hue value.
Value limits can
vary for different devices.
Value is a property of
input connected to current
window. Changing
window input source
might cause changes in
this value (refer device
definitions).
COMMAND
#W-HUEwin_num,value<CR>
FEEDBACK
~nn@W-HUEwin_num,value<CR><LF>
win_num – Window number setting
contrast
value – Hue value
Set window hue value:
#W-HUE1,1<CR>
W-HUE?
Get window hue value.
Value limits can
vary for different devices.
Value is a property of
input connected to current
window. Changing
window input source
might cause changes in
this value (refer device
definitions).
COMMAND
#W-HUE?win_num<CR>
FEEDBACK
~nn@W-HUEwin_num,value<CR><LF>
win_num – Window number setting
contrast
value – Hue value
Get window hue value:
#W-HUE?1<CR>
W-LAYER
Set window overlay order.
Set all window overlay
orders.
In case of
overlays order list,
number of expected
layers is maximum
number of windows in
device.
COMMAND
#W-LAYERwin_num,value<CR>
#W-LAYER0xFF,value1,value2,…,valueN<CR>
FEEDBACK
Set1/Get1:
~nn@W-LAYERwin_num,value<CR><LF>
Set2/Get2:
~nn@W-LAYER0xFF,value1,value2,…,valueN<CR><LF>
win_num – Window number setting
layer
value – Overlay order number
Set window overlay
value:
#W-LAYER1,1<CR>
W-LAYER?
Set window overlay order.
Set all window overlay
orders.
In case of
overlays order list,
number of expected
layers is maximum
number of windows in
device.
COMMAND
#W-LAYER?win_num<CR>
#W-LAYER?0xFF<CR>
FEEDBACK
~nn@W-LAYERwin_num,value<CR><LF>
~nn@W-LAYER0xFF,value1,value2,…,valueN<CR><LF>
win_num – Window number setting
contrast
value – Hue value
Get window overlay
value:
#W-LAYER?1<CR>