Krone Swadro 810 - Settings; Adjusting Rotor Running Gear Inclination

Settings
62
Pos: 22 /Überschri ften/Überschrift en 1/A-E/Einst ellungen @ 0\ mod_119986878 3862_78.doc @ 3 6141
9 Settings
Pos: 23.1 /Übersc hriften/Übersc hriften 2/K-O/Kr eiselfahrwerk ein stellen @ 2\ mod_1202882031 680_78.doc @ 6 2105
9.1 To adjust the rotor running gear
Pos: 23.2 /BA/Eins tellungen/Sch wader/Kreiselfahr werk/Kreiselfa hrwerk Bild Sw adro 907 BJ.2 010 @ 76\mod_1 30977294484 5_78.doc @ 664 458
I
II
III
1
2
I
II
III
Figure 37
Pos: 23.3 /BA/Eins tellungen/Sch wader/Kreiselfahr werk/Kreiselfa hrwerk Text allgemein @ 2\ mod_1202882 266696_78.doc @ 6 2162
The transverse inclination (in direction of travel) and the longitudinal inclination (rotor tip
forwards) of the rotors can be adjusted at the rear guide wheels of the right and left running
gear.
Pos: 23.4 /BA/Eins tellungen/Sch wader/Kreiselfahr werk/Kreiselfa hrwerk Quer neigung @ 2\ mod_120288311885 2_78.doc @ 6 2181
Transverse inclination:
In order to achieve an optimal operating result, the transverse inclination (in direction of travel)
for the right and left rotors can be adjusted individually at the rear guide wheels of the relevant
running gear (left + right).
Pos: 23.5 /BA/Eins tellungen/Sch wader/Kreiselfahr werk/Querneig ung Seitensc hwad SW 807_8 10@ 2\mod_1 20289722849 3_78.doc @ 6230 7
When a side swath is loaded, the right guide wheel must be positioned lower than the left guide
wheel relative to the rotor running gear.
Pos: 23.6 /BA/Eins tellungen/Sch wader/Kreiselfahr werk/Kreiselfa hrwerk vorgeh ensweise Sadro 8 07_810 @ 2\mod_1202883 960133_78.doc @ 6 2219
Do not walk under the raised rotors.
• Raise the rotor arms only far enough to be able to perform the switching task.
• Remove the rear guide wheels and reinstall them in the desired position.
Pos: 23.7 /BA/Eins tellungen/Sch wader/Kreiselfahr werk/Kreiselfa hrwerk Längs neigung Swadro 8 07/810 @ 2\ mod_120288330 1211_78.doc @ 6 2200
Longitudinal inclination:
The longitudinal inclination can be changed (rotor tips forward) by reconnecting the rear guide
wheels (right and left) of the running gear in positions (I,II,III).
Pos. I= least tipping effect
Pos. III= most tipping effect
Pos: 23.8 /BA/Eins tellungen/Sch wader/Kreiselfahr werk/Kreiselfa hrwerk vorgeh ensweise Sadro 8 07_810 @ 2\mod_1202883 960133_78.doc @ 6 2219
Do not walk under the raised rotors.
• Raise the rotor arms only far enough to be able to perform the switching task.
• Remove the rear guide wheels and reinstall them in the desired position.
Pos: 24 /BA/----- Seitenumbruch---- -- @ 0\mod_1 196175311226 _0.doc @ 416 5