What to do if scheduled sending jobs exceeded on Kyocera All in One Printer?
The number of jobs has exceeded the limit set for delayed transmission. Press [OK]. The job is canceled. Wait until the delayed transmission is executed, or cancel the delayed transmission and then perform the job again.
Why can't my Kyocera KM-3050 store memory forwarding data in a FAX Box?
There are two possible causes: * The FAX Box may not be specified correctly. Check the memory forwarding setting. * There may not be enough free space available in the memory. Receive after the memory has free space, or create free space in the memory.
Why can't my Kyocera KM-3050 perform sub address transmission?
There are several possible reasons: * The recipient fax machine may not be equipped with a sub address transmission feature. Sub address transmission cannot be performed unless the recipient fax machine has a similar sub address transmission feature. * The entered sub address or sub address password may not be identical to the sub address or sub address password registered in the recipient fax machine. If your entry is correct, check with the recipient. This machine does not use a sub address password for reception. * There may not be free space available in the memory of the recipient fax machine. Check with the recipient.
Why can't my Kyocera All in One Printer perform memory forwarding?
This issue occurs if memory forwarding is not set to [On]. Check the memory forwarding setting.
Why can't my Kyocera KM-3050 perform memory forwarding using a sub address?
This issue can occur for the following reasons: * The recipient fax machine may not be equipped with a sub address transmission feature. Sub address transmission cannot be performed unless the recipient fax machine has a similar sub address transmission feature. * The entered sub address may not be identical to the sub address registered in the recipient fax machine. If your entry is correct, check with the recipient. This machine does not use a sub address password for reception.
What to do if Kyocera All in One Printer cannot use sub address relay broadcast communication?
This problem arises when there isn't enough free space available in the memory. To resolve this, free up some space in memory and then send, or simply make some free space in memory.
Why can't I send documents from my Kyocera KM-3050?
There are several reasons why you might not be able to send a document: * The modular cord may not be connected correctly. Ensure it is properly connected. * A communication error might be occurring. Remedy the cause of the error and try sending again. * The TX (transmission) restriction might be activated. Cancel the TX restriction.
Why can't I use sub address bulletin board communication on my Kyocera KM-3050 All in One Printer?
This can happen for a few reasons: * The other party’s fax machine may not have the same sort of sub address bulletin board communication function. If the other party’s fax machine does not have the same sort of sub address bulletin board communication function, it cannot receive faxes via a sub address bulletin board. Check with the recipient. * The entered sub address or sub address password may not be correct. If your entry is correct, check with the recipient.
Why can't my Kyocera KM-3050 use polling reception?
This issue arises if polling transmission is not being used correctly on the sending machine. Check with the recipient to ensure they are using polling transmission correctly.
What to do if Kyocera KM-3050 is restricted by Job Accounting?
Fax transmission is prohibited by Job Accounting. No further operation is possible. Press [End]. The job is canceled. Check the setting for Job Accounting.
Power| voltage | 120V |
|---|---|
| frequency | 60Hz |
| current | 11.5A |
System Memory| standard RAM | 512MB |
|---|---|
| maximum RAM | 1GB |
| hard drive capacity | 80GB |
Output Speeds| warm-up time | Within 30 Seconds |
|---|---|
| first copy out time | 3.9 Seconds |
| pages per minute (letter) | 30 |
Weight and Dimensions| width | 23.6" |
|---|---|
| depth | 25.4" |
| height | 29.3" |
| weight | 188 lbs |
Explains basic fax sending using keys and automatic reception.
Provides methods to cancel transmissions and redial numbers.
Details delayed, broadcast, interrupt send, chain dial, and manual operations.
Covers manual reception, remote switch, memory forwarding, and FAX boxes.
Explains sub address, polling, account management, and program dial features.
Explains i-FAX and details necessary SMTP/POP3 server configuration via Command Center.
Guides on sending and receiving faxes over the Internet.
Lists common error messages and provides a guide to resolve operational problems.
To Next Page
