507343-01
Page 16
Complete iComfort
®
System — Adjusting Dehumidification Settings
SYSTEM DEVICES SCREEN — DEHUMIDIFICATION SETTINGS
edit
about
To adjust a setting,
highlight it,
then press Edit
System
reinstall
edit
reset
De-humidification Control Mode
current value:
back
Midpoint Overcooling
1. In the “system devices” list, use the arrows (1a) to
highlight System. Press edit (1b).
2. Humiditrol
®
only—In the “System” list, use the ar
rows (2a) to highlight Humiditrol Comfort Adjust.
The current value defaults to Maximum Overcooling.
Press edit (2b).
3. Humiditrol
®
only—Touch one of the radio buttons
(3a) to select the overcooling level; press save (3b).
(After saving, check that the current value now shows
the new selection).
4. Use arrows (4a) to highlight Min De-humidification
Setpoint; press edit (4b). Note the current value
(e.g. 45).
5. Use arrows (5a) to make changes; press save (5b).
(After saving, check that the current value now shows
the new selection).
6. Press the back button to return to “Adjust a setting...”
screen.
1a
1b
2a
system devices
System
Air Conditioner
Furnace
Thermostat
Humiditrol
Maximum Overcooling Midpoint Overcooling
Minimum Overcooling
Select one
Humiditrol Comfort Adjust
cancelsave
3b
3a
System
3rd Stage Delay
4th Stage Delay
Lock In 2nd Stage HP by Outdoor Temp
Balance Point Control
Humiditrol Comfort Adjust
Min De-humidification Setpoint
edit
reset
back
De-humidification Control Mode
current value:
45
9:39 am Aug 15, 2012
4a 4b
Humiditrol Comfort Adjust settings are
only available on units equipped with
a Humiditrol
®
De-humidification
device.
resetAll
2b
6
Min De-humidification
Setpoint
Range is 40 to 60
Default is 45, inc:1
cancel
save
set-to
42 %
5a
5b
(returns to
adjust a
setting
screen)
System
Staged Delay TImers
2nd Stage Delay
3rd Stage Delay
4th Stage Delay
Lock In 2nd Stage HP by Outdoor Temp
Balance Point Control
Humiditrol Comfort Adjust
Min De-humidification Setpoint
OD/Humid Boundary
Outdoor Temperature Reading Calibr
Pre-adjustment REQUIREMENTS:
1st, the device has been installed
2nd, from the “Add or Remove Non-communicating
equipment?”, press next.
3rd, in the “Adjust a setting...” screen, configure the
device as follows:
Figure 12. Complete iComfort
®
System Devices — Dehumidification Settings
FEATURE SCREEN — DEHUMIDIFICATION SETTINGS
1. From the Main Screen, press the right arrow icon to go the
the Features screen.
2. From the Features screen, select system settings.
3. Touch the ClimateIQ setting button. Available options
when selected are selection for DRY, MODERATE and
HUMID.
4. Selecting HUMID bring on the set-to button. When you
touch the set-to button, the arrows appear, allowing you to
change to the desired dehumidifier percentage setting
SYSTEM SETTINGS
heating
mode
COMFORT
humidifier
is ON
ClimateIQ
setting
MOD
humidifier
display
is ON
Appears only when
heat pump is
present
humidification
settings
De-humidification settings
(default is DRY)(default is ON)
(default is ON)
Select the humidity
level that matches
your environment
9:39 am Aug 15, 2012 ?
Wi-Fi
35
%
set to
40
%
set to
HEATING MODE (XP25 ONLY) — CLIMATE IQ™
This technology optimizes dehumidification settings
for specific climates to improve home comfort during
cooling or heating operations.
Two climate settings are available:
Comfort The system reduces indoor airflow, in
creasing supply air temperature.
Normal Standard system operation.
COOLING MODE — CLIMATE IQ™
Three climate settings are available:
Dry The system supplies higher indoor airflow at all com
pressor capacities, increasing efficiency by operating at a
higher sensible-to-total ratio.
Moderate The system supplies indoor airflow that balances
efficiency and comfort.
Humid - The system supplies lower indoor airflow at all com
pressor capacities, improving humidity removal by operating
at a lower sensible to total ratio.
Figure 13. Dehumidification iComfort
®
System Controls
To Next Page
Loading...
