Lennox icomfort Wi-Fi - System Devices Screen - Humiditrol Comfort Adjustment

507343-01
Page 20
Partial iComfort
®
System — Adjusting Dehumidification Settings (Non-Communicating
Outdoor Unit)
SYSTEM DEVICES SCREEN — HUMIDITROL COMFORT ADJUSTMENT
edit
about
To adjust a setting,
highlight it,
then press Edit
System
reinstall
edit
reset
De-humidification Control Mode
current value:
back
Midpoint Overcooling
1. In the “system devices” list, use the arrows (1a) to
highlight System. Press edit (1b).
2. Humiditrol
®
only—In the “System” list, use the ar
rows (2a) to highlight Humiditrol Comfort Adjust.
The current value defaults to Maximum Overcooling.
Press edit (2b).
3. Humiditrol
®
only — Press one of the radio buttons
(3a) to select the overcooling level; press save (3b).
(After saving, check that the current value now
shows the new selection).
4. Use arrows (4a) to highlight Min De-humidification
Setpoint; press edit (4b). Note the current value
(e.g. 45).
5. Use arrows (5a) to make changes; press save (5b).
(After saving, check that the current value now
shows the new selection).
6. Press the back button to return to “Adjust a set
ting...” screen.
1a
1b
2a
system devices
System
Air Conditioner
Furnace
Thermostat
Humiditrol
Maximum Overcooling Midpoint Overcooling
Minimum Overcooling
Select one
Humiditrol Comfort Adjust
cancelsave
3b
3a
System
3rd Stage Delay
4th Stage Delay
Lock In 2nd Stage HP by Outdoor Temp
Balance Point Control
Humiditrol Comfort Adjust
Min De-humidification Setpoint
edit
reset
back
De-humidification Control Mode
current value:
45
9:39 am Aug 15, 2012
4a 4b
Humiditrol Comfort Adjust set
tings are only available on units
equipped with a Humiditrol
®
De-humidification device.
resetAll
2b
6
Min De-humidification
Setpoint
Range is 40 to 60
Default is 45, inc:1
cancel
save
set-to
42 %
5a
5b
(returns to
adjust a
setting
screen)
System
Staged Delay TImers
2nd Stage Delay
3rd Stage Delay
4th Stage Delay
Lock In 2nd Stage HP by Outdoor Temp
Balance Point Control
Humiditrol Comfort Adjust
Min De-humidification Setpoint
OD/Humid Boundary
Outdoor Temperature Reading Calibr
Pre-adjustment REQUIREMENTS:
 1st, the device has been installed
 2nd, from the Add or Remove Non-communicating equip
ment?, press next.:
 3rd, in the Adjust a setting... screen, configure the device
as follows
Figure 16. Adjust a Non-Communicating Device Setting — Dehumidification
FEATURE SCREEN — DEHUMIDIFICATION SETTINGS
1. From the main screen, press the right arrow icon to go
the the Features screen.
2. From the Features screen, select system settings.
3. Touch the button of the dehumidification settings you
want to adjust; if it says dehumidifier OFF, one touch will
display a selection for OFF, MEDIUM or HIGH.
4. Selecting MEDIUM or HIGH will bring on the set-to but
ton.
5. When you touch the set-to button, the arrows appear, al
lowing you to change to the desired dehumidifier per
centage setting
SYSTEM SETTINGS
current indoor humidity is 50%
humidifier
is ON
de-
humidifier
MEDIUM
40
%
set to
50
%
set to
ALL CHANGES MADE ON
THIS SCREEN ARE IN
STANTLY SAVED.
9:39 am Aug 15, 2012
?
Wi-Fi
OFF
MEDIUM
HIGH
humidifier
display
is ON
(default is ON)
humidification
settings
De-humidification
settings
Figure 17. Dehumidification Settings Controls