Lenze 9300 Series - Page 451

Appendix
Index
14
14.2

14.2−3
EDSVF9383V EN 7.1−04/2012
Display
− Application datum, 9.1−1
− operating status, 9.2−1
Display functions, 9.1−1
− Possible values, 9.1−1
Display of operating data, 9.1−1
Display values, 9.1−1
− Calibration, 9.1−1
Disposal, 2.1−3
Distributed supply, 10.3−1
Drive behaviour
− Controller inhibit, 6.4−1
− in the event of faults, 9.3−1
Drive errors, 9.4−1
E
E.l.c.b., 5.2−2
− operation at, 5.2−2
Earth fault in motor cable (OC2), 8.3−3
Earth−leakage circuit breaker, 5.2−2
− operation at, 5.2−2
Electrical installation, system bus (CAN), 5.7−1
EMC, what to do in case of interferences, 5.3−6
Emergency−off, Controller inhibit, 6.4−1
EMZ9371BC keypad, changing parameters, 7.2−7 , 7.2−8
EN 61000−3−2, 5.2−1
− operation on public supply systems, 5.2−1
Entry of motor data, 6.6−1
Error analysis, Via history buffer, 9.2−1
Error messages, 9.5−1
− causes and remedies, 9.5−1
− configuration, 8.4−1
− General, 9.5−1
− Resetting, 9.5−5
Exceeding of the maximum speed (NMAX), 8.3−3
Explanations, Code table, 8.5−1
External brake resistors, 12.2−1
External error (EEr), 8.3−8
F
Failure of a motor phase, 8.3−4
Fan connection, 400/500 V devices, 5.4−4 , 5.5−8
Fan connection EVx9335 ... EVx9383
− Controller is supplied via the DC bus, 5.4−5 , 5.5−9
− controller is supplied with mains voltage, 5.4−4 , 5.5−8
Fault analysis, Via history buffer, 9.2−1
Fault elimination, 9.4−1
Fault messages
− causes and remedies, 9.5−1
− OC3 in clamp operation, 9.4−2
Fault responses, 8.3−1
Feedback system, wiring, 5.8−1
Field controller, 6.8−8 , 8.5−8
Field frequency
− maximum, 6.10−1
− Minimum, 6.10−1
Free mounting spaces, 4.1−1
Free spaces, 3.1−2
Function blocks, 8.2−1
− diameter calculator (DCALC1), 8.2−1
− internal motor control, vector control (MCTRL2), 8.2−40
− master frequency input (DFIN), 8.2−5
− master frequency output (DFOUT), 8.2−8
− master frequency processing (DFSET), 8.2−18
− master frequency ramp−function generator (DFRFG1),
8.2−13
Function keys, keypad XT EMZ9371BC, 7.2−4
Functional test, safety function, 11.4−2 , 11.4−5
Fuses, 10.2−1
G
gases, aggressive, 4.1−1
General accessories, 13.1−1
General data, 3.1−1 , 7.2−1
H
Harmonic currents, Limitation according to EN 61000−3−2,
5.2−1
Heatsink temperature, monitoring, 8.3−7
History buffer, 9.2−1
− Assembly, 9.2−2
− clear, 9.2−2
I
Imax limit in generator mode, in generator mode, 6.6−14 ,
8.2−27 , 8.2−42 , 8.5−4