Lexmark C912 User Manual (English)

Other manuals for Lexmark C912

User Reference Guide207 pages

Quick Reference2 pages

Questions and Answers:

M
Matthew ThompsonAug 18, 2025
How to fix Lexmark C912 Printer when job did not print or incorrect characters printed?
- L
  lauren82Aug 18, 2025
  To resolve print job issues or incorrect characters on your Lexmark Printer, ensure 'Ready' is displayed on the operator panel. If not, press 'Go'. Also, confirm that the print media is properly loaded and that you're using the correct printer language and driver. Check the parallel, serial, ethernet, or USB cable connections, ensuring they are securely plugged in. For parallel connections, use an IEEE 1284-compliant cable. If connected through a switch box, try a direct connection. Verify the paper size selected is correct in the operator panel, driver, and software. Finally, ensure PCL SmartSwitch and PS SmartSwitch are enabled.
M
Marie HurleyAug 20, 2025
How to troubleshoot Lexmark Printer when job did not print or incorrect characters printed (continued)?
- J
  Jacob EstradaAug 21, 2025
  If a print spooler is in use, verify it is not stalled. Check the printer interface from the Setup Menu to determine the host interface being used. Print a menu settings page to verify the current interface settings. If using a serial interface, ensure 'Honor DSR' is set to Off, and check the protocol, baud, parity, and data bit settings, ensuring they match on both the printer and host computer.
K
Karina WaltonAug 23, 2025
Why does Lexmark C912 Printer seem to print slowly?
- N
  Nicole CarpenterAug 23, 2025
  To address slow printing on your Lexmark Printer, ensure the appropriate Paper Type setting is selected. Note that the Transparency setting slows printing to adjust the fuser temperature for better print quality, requiring additional warm-up time when switching back to other paper types like Plain Paper or Letterhead. Reducing the complexity of your print job by minimizing the number and size of fonts, the number and complexity of images, and the number of pages can also increase print speed. Additionally, set Page Protect to Off in the Setup Menu.
M
Martha BarajasAug 26, 2025
What to do if Lexmark C912 print media misfeeds or multiple feeds occur?
- J
  Jordan Fernandez PhDAug 26, 2025
  To resolve paper misfeeds or multiple feeds on your Lexmark printer, ensure the print media meets the printer's specifications. Flex the print media before loading. Verify that the print media is loaded correctly and that the paper width and length guides are properly adjusted. Avoid overfilling the paper sources or forcing media into the multipurpose feeder. Remove any curled print media and ensure the correct print side is loaded. Try using less print media, turning it over, and avoiding mixing different types or reams. Remove the top and bottom sheets of a ream and only load a paper source when it is empty.
R
Robert ClarkAug 28, 2025
How to resolve paper does not feed properly on Lexmark C912 Printer?
- K
  Kelly TorresAug 28, 2025
  To fix paper not feeding properly in your Lexmark Printer, ensure you're using recommended media. Avoid using 16 lb paper or paper heavier than 32 lb with the duplex unit. Make sure the adjustable guides in the paper tray are properly set for the loaded media and that the media stack doesn't exceed the maximum height indicated on the tray.
H
Heather TaylorAug 30, 2025
What to do if Lexmark C912 envelope misfeeds or multiple feeds occur?
- J
  Joseph BurnsAug 30, 2025
  To address envelope misfeeds or multiple feeds in your Lexmark Printer, remove the stack of envelopes from the multipurpose feeder. Load one envelope, feed it through the printer, and then reload the stack. Also, push down the bottom plate until it locks into place.
M
Mary LeeSep 2, 2025
Why do transparencies jam in Lexmark C912 Printer?
- H
  hessrobertoSep 2, 2025
  To resolve the issue of transparencies jamming in your Lexmark Printer, if the printer has just been turned on or has been idle, print on paper first. Disabling the Power Saver feature may also prevent transparencies from jamming after the printer has been idle.
X
xsanfordSep 4, 2025
What to do if paper is jammed in the fuser of Lexmark C912 Printer?
- R
  Richard DouglasSep 5, 2025
  If paper is jammed in the fuser of your Lexmark Printer, rotate the fuser pressure release lever down and remove the jammed paper.
M
michelleblakeSep 7, 2025
Why does Lexmark C912 Printer not duplex pages?
- J
  Jennifer MartinSep 7, 2025
  To address the issue of a Lexmark Printer not duplexing pages, ensure that the Duplex setting is selected in either the Finishing Menu or the program you are printing from. Also, verify that you have sufficient printer memory installed.
J
Julia SanchezSep 9, 2025
Why does Lexmark C912 Printer job print from the wrong paper source or on the wrong print media?
- V
  vryanSep 10, 2025
  To resolve the issue of a Lexmark Printer printing from the wrong paper source or on the wrong print media, check the Paper Type setting in the Paper Menu on the printer operator panel and in the printer driver.