What to do if the contactor has not closed on load on my Liebert 7200?
If the contactor has not closed on load at the correct time on your Liebert UPS, and the load is probably on bypass (if allowable), seek qualified assistance.
General| Category | UPS |
|---|---|
| Brand | Liebert |
| Series | 7200 Series |
| Frequency | 50/60 Hz |
| Phase | 3-Phase |
| Dimensions | Varies by model |
| Weight | Varies by model |
| Topology | Double Conversion |
| Battery Type | VRLA |
| Operating Temperature | 0°C to 40°C |
| Humidity | 0% to 95% (non-condensing) |
Provides an overview of the UPS system and its advantages.
Explains the fundamental operating principles and architecture of the UPS.
Details the static and maintenance bypass functionality for load protection.
Describes the layout and function of the UPS power switches.
Covers battery circuit breakers, cabinets, and temperature compensation.
Introduction to the panel for monitoring and controlling the UPS.
Diagram and description of the UPS status and alarm LEDs.
Details the function and operation of the EPO switch.
Description of the LCD display, its operation, and panel messages.
Information on how alarms and warnings are indicated and selected.
Outlines the three main operating conditions of the UPS system.
Step-by-step guide to starting the UPS from a fully powered-down state.
Instructions for transferring the load to bypass for maintenance.
Guide to restarting the UPS from a maintenance shutdown.
Steps to safely shut down the UPS and disconnect power.
Procedure to reset the UPS after specific fault conditions or EPO activation.
Overview of installation procedures, requirements, and warnings.
Details safety precautions specifically related to handling batteries.
Lists essential checks to perform before installing the UPS hardware.
Guidance on connecting input, output, and battery power cables.
Describes the pathways for routing cables into the UPS cabinet.
Provides recommended cable sizes based on UPS rating and current.
Explains how to make physical connections to busbars and terminals.
Details essential procedures for proper earthing and bonding.
Information on selecting and installing circuit breakers and fuses.
Step-by-step instructions for connecting power cables to the UPS.
Diagram showing external cable routing and connection points.
Diagram illustrating power and control cable interconnections.
Specific instructions for connecting battery power cables.
Wiring instructions for the remote EPO functionality.
Details the AS400 interface board for connecting UPS alarms to IBM AS400 systems.
Describes the board for extending alarm outputs to remote monitoring devices.
Provides information on the remote monitor for displaying alarm status.
Covers the specifications and types of optional battery cabinets available.
Details optional boxes for battery isolation circuit breakers.
Information on optional input harmonic filters for power factor improvement.
Describes kits for connecting the UPS to PCs or modems for monitoring.
Overview of recommended periodic maintenance activities for the UPS.
Routine daily inspection procedures for the UPS control panel and environment.
Weekly checks involving measurement and recording of UPS parameters.
Detailed annual maintenance procedures, often requiring internal access.
Recommendations for periodic checks of power cables and connections.
Guidelines for maintaining the UPS battery system.
Instructions on how to view and interpret UPS operating status parameters.
General guidance and approach to diagnosing UPS faults.
Key operational limits and parameters to monitor for fault detection.
Methodical steps for identifying and correcting UPS problems.
Instructions on how to report detected faults to service agents.
Detailed explanation of the meaning of each LED indicator on the UPS panel.
Explanation of the various alarm and warning messages shown on the UPS display.
Introduction to the 1+1 parallel UPS system configuration.
Description of the redundant parallel configuration and its operation.
Description of the power parallel configuration and its operation.
Overview of separate vs. common battery configurations for parallel systems.
Installation steps for parallel systems using separate battery configurations.
Pre-installation checks specific to parallel operation with separate batteries.
Cable requirements for parallel operation with separate batteries.
Details on connecting control and communication cables for parallel systems.
Wiring for EPO functionality in parallel systems.
Procedures for starting and stopping parallel UPS systems with separate batteries.
Steps to start up a 1+1 parallel system with separate batteries.
Procedure to transfer load to maintenance bypass in parallel systems.
Steps to restart a parallel system after maintenance shutdown.
Procedure to isolate one UPS in a redundant parallel setup.
Procedure to re-enable an isolated UPS in a redundant parallel setup.
Installation steps for parallel systems using a common battery configuration.
Details on connecting to the auxiliary distribution box for common battery systems.
Procedures for starting and stopping parallel UPS systems with a common battery.
Steps to start up a 1+1 parallel system with a common battery.
Procedure to bypass the UPS for maintenance in common battery systems.
Steps to return from maintenance bypass to normal operation.
Procedure to isolate one UPS in a common battery parallel setup.
Procedure to re-enable an isolated UPS in a common battery parallel setup.
Specifications related to the physical dimensions, weight, and construction of the UPS.
Details operating and storage environmental conditions for the UPS.
Specifications for the UPS's input voltage, current, and frequency.
General system data including efficiency, losses, and overload capabilities.
Specifications for the UPS's output voltage, frequency, current, and distortion.
Technical specifications related to the internal DC circuit parameters.
Specifications concerning the static switch performance.
Specifications for the different types of optional battery cabinets.
Specifications for the optional battery circuit breaker boxes.
To Next Page
