Need help?Do you have a question about the Link G4 Storm and is the answer not in the manual?
Provides options for obtaining technical support for installation issues.
Details the configuration and specifications for the ECU's injector drives.
Explains the configuration and use of the ECU's ignition output channels.
Covers the functionality and limitations of the ECU's general-purpose auxiliary outputs.
Describes how to connect and configure analog and temperature sensors to the ECU.
Explains the setup and use of digital inputs for switches and sensors.
Details the setup of engine speed and position sensors for accurate ECU operation.
Provides a summary table for basic configuration of inputs and outputs.
A table to assist in planning and configuring ECU inputs and outputs for installation.
Guidelines for selecting an appropriate and safe mounting location for the ECU.
Recommendations for placing ignition components to minimize interference and ensure reliability.
Guidance on selecting the optimal location for the Manifold Absolute Pressure sensor.
Details the recommended wiring arrangement for supplying power to the ECU.
Explains the connection and importance of the primary +14V power input for ECU operation.
Covers the +14V power supply for specific auxiliary drivers on Xtreme ECUs.
Essential guidelines for correctly grounding high current output drives.
Critical information on providing a stable ground reference for all sensors.
Describes the regulated +5V output used for powering sensors.
Details the regulated +8V output for specific sensors like Crank Angle Sensors.
Explains a wiring method to keep the ECU powered after the ignition is switched off.
Essential setup for engine speed and position sensors for accurate ECU operation.
Wiring and polarity considerations for reluctor and magnetic trigger sensors.
Wiring details for Hall effect, optical, and proximity type trigger sensors.
Instructions for wiring and connecting the Manifold Absolute Pressure sensor.
Details on connecting the Throttle Position Sensor for load sensing and other functions.
Wiring and setup for the Engine Coolant Temperature sensor.
Guides for installing and wiring the Intake Air Temperature sensor.
Information on wiring and using narrow band oxygen sensors.
Details on connecting wide band oxygen sensor controllers to the ECU.
How to wire general purpose pressure and temperature sensors.
Methods for wiring switches and controllers to digital input channels.
Covers wiring and configuration for controlling fuel injectors with the ECU.
Wiring instructions for high impedance fuel injectors.
Instructions for wiring low impedance injectors, including ballast resistor use.
Details available injection modes like Sequential, Group, and Staged.
Explains how ignition drives are used for various ignition system configurations.
Information on igniters as interfaces between the ECU and ignition coils.
Guidance on selecting and wiring ignition coils based on application needs.
General guidelines for wiring ignition systems, including suppression techniques.
Wiring setup for engines using a distributor for ignition timing.
Details on wiring wasted spark ignition systems using dual post coils.
Wiring configurations for direct spark ignition systems with one coil per cylinder.
Comprehensive guide to wiring and configuring auxiliary outputs for various functions.
Wiring method for actuating loads by grounding through auxiliary outputs.
Wiring method for actuating loads by supplying power via auxiliary outputs.
Instructions for using a relay to switch large loads connected to auxiliary outputs.
How to wire an LED, typically for warning or shift lights, to an auxiliary output.
Explanation of the ECU's Idle Speed Control system and its operation.
Wiring instructions for two-terminal Idle Speed Control solenoids.
Details for wiring three-terminal Idle Speed Control solenoids.
Wiring guide for four-terminal Idle Speed Control stepper motors.
Wiring instructions for six-terminal Idle Speed Control stepper motors.
How to configure an auxiliary output to drive a low-level tachometer.
Wiring and configuration for Variable Valve Timing solenoids.
Information on the Electronic Throttle Control feature and its wiring.
Specific injector wiring configurations for rotary engines.
Ignition wiring setups tailored for rotary engine configurations.
Details on wiring the rotary engine's metering oil pump control.
Instructions for installing the necessary USB drivers for ECU communication.
Guide to downloading and installing the PCLink tuning software application.
Steps to establish a connection between the PC and the ECU for tuning.
Essential checks to perform before attempting to configure or start the engine.
Basic configuration steps for fuel injection and engine parameters.
Configuration of ignition timing, advance, and dwell time settings.
Setting operational limits to prevent interference with tuning procedures.
Configuration of ECU auxiliary outputs for connected devices.
Configuration of ECU digital input channels for sensors and switches.
Configuration of ECU analog input channels for sensors.
Crucial setup of engine speed and position sensors for ECU operation.
Configuration of non-essential tuning features like Antilag and Launch Control.
Procedure for calibrating trigger inputs to ensure accurate engine timing.
Step-by-step guide for starting the engine for the first time after setup.
Key adjustments for MAP sensor calibration and injector dead time correction.
General| Number of Outputs | 8 |
|---|---|
| Injection Type | Sequential / Grouped |
| Ignition Type | Direct Spark / Distributor |
| Type | Engine Control Unit |
| Inputs | Analog, Digital, Frequency |
| Outputs | Injector, Ignition, Auxiliary |
| Operating Temperature | -20°C to 70°C |
To Next Page