Troubleshootin
If
a
problem
occurs, first check
the
following:
1.
Are
the
connections correct?
2.
Is
the
unit
being operated as described in
the
owner's
manual?
3. Are
the
other components operating
properly?
If
this unit does not operate
properly,
check the items listed in the
table below. If
the
problem
persist there may be a
malfunction.
In
that case, disconnect the power
immediately
and contact your
retail
out
let.
:c.•
·
..
,
,J
" ·.
sviriP'foffi
~·
:
'
.'.'
··
"'
'
:~
'l~;.%.
' .
,
·
·
·
~
·
• ' ·
;;;
·
~
cau.-
.
..:
;
~;:\[!
,;;;
J.;;~
~
'
"'
~T
·~
'{''
El
~
'
' •
•
,s•
.,
..
•,:
c.
C
.
o
.
unt~i:fn·ii.U~e
·',1•
,,
,.
""
•
•"
jc'···
••.
:
~~
·
\-t
!
..
f:-
,.,..
Power
is not turned on.
•
The po
wer
cord's
plug
is not
plugged
in
firmly. •
Make
sure that the power cord is
plugged
in
properly.
•
The unit
is
in standby mode.
•
Either turn the
INPUT SELECTOR
knob
of
this
un
it or press
POWER
ON
of
the remote
control.
•
The protection circuit
is
activated.
•If
the
STANDBY
indi
ca
tor is
blinking,
turn
off
power, wait 1 minu
te
or
longer,
and turn on
power
again.
When power
is
turned on but there is
•
The speaker
cables are not
proper
ly
connected.
• Make
su
re t
he
speakers are connected
properly.
no sound.
•
The input
cable
is
not
properly
connected.
• Make sure t
he
inp
ut
cables
are connected
properl
y.
•
The
INPUT
SELECTOR
knob setting position is incor
re
ct.
• Set
the
IN
PUT
SELECTOR
knob at the
correct
sett
i
ng
position.
•
The
VOLUME control
knob is set to minimum.
•
Use the
VO
LU
ME control
knob to turn
volu
me
up to
an
app
ro
priate
level.
• The
SPEAKERS
AJB
switches are turned off.
•
Turn on
the
SPEAKERS
AJB
sw
itch corresponding to the speaker system
terminals
(SYS
TEM
A
or
SYSTEM
B)
to
which the speakers are connected.
•
The incorrect
SPEAKERS
AJB
switch
is
turned on.
•
Turn on the
SPEAKERS
AJB
sw
it
ch
corresponding
to
the speaker system
termi
na
ls
(SYS
TEM
A or
SYSTEM
B)
to
which the speakers are connect
ed.
•
The mute function activated.
• If
the MUTE indi
ca
tor
is
lit.
press MUTE on the remote control
to
cancel
mut
ing.
The
volume
drops automatically.
•
The protection circuit is activated.
•
Turn
off
power, wait 1 minute or longe
r,
and turn on power
agai
n.
Sound
is
produced f
ro
m either one
•
The speaker cables are
not
properly
connected.
• Make sure that the speakers are connected
properly.
speaker
only.
•
The BALAN
CE
control
knob set
ti
ng
position is inapprop
ria
t
e.
• Set
the
BALANCE control
knob at the appropriate position .
The
left
and right
channels
are
•
Either the
left/right
speaker or left/right
input
cable • Make sure that the speakers are connected correctly.
reversed.
connections
are
reversed.
Noise
is
produced during a record
•
The ground wire
fr
om the
turntable
is
disconnected.
•
Make sure that the
PHONO
GND
term
i
na
l
is connected properl
y.
playback.
•
The
PHONO input
terminals
are not
properly
connected.
• Ma
ke
sure that the
PHONO
input
term
in
al
is connected properly.
•
A
TV
set near the
turntable
is
ca
using the noise.
• Relocate
the
TV
set or
turntable
in
another place.
An audio feedback occurs when you
•
The
turntable
and speakers are too close
to each other.
• Install
t
he
speakers
as
far away
fr
om the
turntable
as
possible.
turn up the
volume during a record
•
The
turntable
is
placed
on a rack or
floor
that vibrates
easily.
• If
the
turntable
is
not supplied
with
an
insulating
pad,
use insulating pad
avai
lable
in the
playback.
market.
The unit does not function when a
• Batteries
are
low
.
• Replace
w ith
new
batteries.
remote
control
button is pressed.
•
You are operating the remote
cont
rol
outside
of
the specified
• Operate within the specified range.
range.
•
There is
an
obstacle
betwe
en t
he
main unit and remote
•
R
emo
te the
obstacle.
control.
•
You have pressed the wrong button.
• Press
the correct button.
•
Batte
ri
es are not inserted
in
the proper direction
as
indicated
• Insert
the batteries in the proper direction in accordance with the
polarity
markers in
the
by
polari
ty
markers
(Ef)
and
8 )
in the battery compartment. battery compar
tm
ent.
•
The remote sensor function
of
this unit
is
disabled.
•
Make sure the remote control sensor function is
enabled.
•
The remote
control code set for this unit does not match the
• Set
the same remote control
code
fo
r this unit and remote
contr
ol.
code of its remote
control.
ENGLISH
{
~
l!i
•
p~
.,
,
.
,,
8
8
6
7
7
9
9
9
9
9
6
7
9
7
7
7
-
-
-
3
3
3
5
3
11
11
13
'"
"
?.
~
"'
"'
;:>
"'
Q..
--
--
-
To Next Page
Loading...
Need help?
General
Weight and Dimensions
