168
APPX
Appendix 1 List of Buffer Memory Addresses (for Synchronous Control)
■Synchronous parameter: Main shaft
n: Axis No. - 1
■Synchronous parameter: Auxiliary shaft
n: Axis No. - 1
Item Fetch cycle Buffer memory address
Axis 1 to axis 16
[Pr.400] Main input axis No. At operation start (Synchronous control) 36400+200n
[Pr.401] Sub input axis No. At operation start (Synchronous control) 36401+200n
[Pr.402] Composite main shaft gear Operation cycle 36402+200n
[Pr.403] Main shaft gear: Numerator At operation start (Synchronous control) 36404+200n
36405+200n
[Pr.404] Main shaft gear: Denominator At operation start (Synchronous control) 36406+200n
36407+200n
[Pr.405] Main shaft clutch control setting Operation cycle 36408+200n
[Pr.406] Main shaft clutch reference address setting At operation start (Synchronous control) 36409+200n
[Pr.407] Main shaft clutch ON address Operation cycle 36410+200n
36411+200n
[Pr.408] Movement amount before main shaft clutch ON At completion of the condition (Clutch
ON)
36412+200n
36413+200n
[Pr.409] Main shaft clutch OFF address Operation cycle 36414+200n
36415+200n
[Pr.410] Movement amount before main shaft clutch OFF At completion of the condition (Clutch
OFF)
36416+200n
36417+200n
[Pr.411] Main shaft clutch smoothing method At operation start (Synchronous control) 36418+200n
[Pr.412] Main shaft clutch smoothing time constant At operation start (Synchronous control) 36419+200n
[Pr.413] Slippage at main shaft clutch ON At completion of the condition (Turning
clutch ON)
36420+200n
36421+200n
[Pr.414] Slippage at main shaft clutch OFF At completion of the condition (Turning
clutch OFF)
36422+200n
36423+200n
Item Fetch cycle Buffer memory address
Axis 1 to axis 16
[Pr.418] Auxiliary shaft No. At operation start (Synchronous control) 36430+200n
[Pr.419] Composite auxiliary shaft gear Operation cycle 36431+200n
[Pr.420] Auxiliary shaft gear: Numerator At operation start (Synchronous control) 36432+200n
36433+200n
[Pr.421] Auxiliary shaft gear: Denominator At operation start (Synchronous control) 36434+200n
36435+200n
[Pr.422] Auxiliary shaft clutch control setting Operation cycle 36436+200n
[Pr.423] Auxiliary shaft clutch reference address setting At operation start (Synchronous control) 36437+200n
[Pr.424] Auxiliary shaft clutch ON address Operation cycle 36438+200n
36439+200n
[Pr.425] Movement amount before auxiliary shaft clutch ON At completion of the condition (Clutch
ON)
36440+200n
36441+200n
[Pr.426] Auxiliary shaft clutch OFF address Operation cycle 36442+200n
36443+200n
[Pr.427] Movement amount before auxiliary shaft clutch OFF At completion of the condition (Clutch
OFF)
36444+200n
36445+200n
[Pr.428] Auxiliary shaft clutch smoothing method At operation start (Synchronous control) 36446+200n
[Pr.429] Auxiliary shaft clutch smoothing time constant At operation start (Synchronous control) 36447+200n
[Pr.430] Slippage at auxiliary shaft clutch ON At completion of the condition (Turning
clutch ON)
36448+200n
36449+200n
[Pr.431] Slippage at auxiliary shaft clutch OFF At completion of the condition (Turning
clutch OFF)
36450+200n
36451+200n
To Next Page
Loading...
