EasyManuals Logo

Mitsubishi HC4000 User Manual

Mitsubishi HC4000
48 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #6 background imageLoading...
Page #6 background image
EN-6
2
3
1
What’s included in the box
AC power cord
1 RGB cable for PC
for US J2552-0063-03
for EU J2552-0066-02
for UK J2552-0065-02
J2552-0072-05
1 Remote control
1 User Manual/Quick Start up (English only)
1 Safety Manual/Quick Start up
1 CD-ROM (with User Manual)
2 Battery
1 Lens cap
1 Lamp replacement attachment
Important:
The attached power cords are to be used exclusively for this product. Never use them for other products.
Inserting the batteries into the remote control
Remove the back lid of the remote control.
Check the polarity (+), (-) of the batteries, and set them
correctly, inserting their (-) side first.
If the battery is inserted from the (+) side first, inserting
the (-) side is difficult because the coil spring end hits
on the battery side. If the battery is forced in this way,
the outer label of the battery may get ripped and it may
cause a short-circuit and heating.
Attach the back lid.
Important:
Use two size-AA batteries (R6).
Replace the two batteries with new ones when the
remote control is slow to respond.
Removing the batteries from the remote control
Remove the back lid of the remote control and take out the batteries.
Caution:
Use of a battery of wrong type may cause explosion.
Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.
Dispose of used batteries according to your local regulations.
Batteries may explode if misused. Do not recharge, disassemble, or throw them in fire.
Be sure to handle the batteries according to the instructions.
Load the batteries with its positive (+) and negative (-) sides correctly oriented as indicated on the remote control.
Keep batteries out of reach of children and pets.
Remove the batteries, if the remote control is not used for a long time.
Do not combine a new battery with an old one.
If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in
contact with your eyes, rinse them with water and then consult your doctor.
1.
2.
3.
Preparing your projector

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Mitsubishi HC4000 and is the answer not in the manual?

Mitsubishi HC4000 Specifications

General IconGeneral
Matrix size0.65 \
Native aspect ratio-
Projection distance- m
Vertical scan range50 - 85 Hz
Horizontal scan range15 - 80 kHz
Projection technologyDLP
Supported aspect ratios4:3, 16:9
Contrast ratio (typical)4000:1
Screen size compatibility50 - 300 \
Projector native resolution1080p (1920x1080)
FocusManual
Focal length range- mm
Lamp power230 W
Light source typeLamp
Lamp power (economic mode)190 W
Service life of light source3000 h
Service life of light source (economic mode)5000 h
Serial interface typeRS-232
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Ethernet LANNo
Full HDYes
Supported video modes1080i, 1080p, 480i, 480p, 576i, 576p, 720i, 720p
Analog signal format systemNTSC, NTSC 4.43, PAL, PAL 60, PAL M, PAL N, SECAM
PlacementDesktop
Product typeStandard throw projector
Product colorBlack
Power sourceAC
AC input voltage100 - 240 V
AC input frequency50 - 60 Hz
Power consumption (standby)- W
Power consumption (typical)340 W
Noise level31 dB
Noise level (economic mode)25 dB
Dot clock scanning frequency170 MHz
Weight and Dimensions IconWeight and Dimensions
Weight3600 g

Related product manuals