17
• The unit of tension (N or × 10N) and the decimal point position are determined by setting the parameter.
• The DISPLAY SELECTOR (TENSION /OUTPUT) switches over the tension display and output display.
• On the screen of Tension set, Stall set, New reel set, Taper ratio, the internal setting or the external setting
which is effective is displayed on the screen. When the external setting is effective, "EXT." is displayed on
the screen, and the internal setting is effective, regisitered menu title is displayed on the screen. (Refer to
page 37~39.)
%:
T P E R S E T
C N R 4 # # # # m m φ → T P R . 4 # # #
A
% T P R . 3 # # #
New reel set ( When “REELS” mode is selected. )
ST
Linear taper set ( When “TAPER” is set to “ON”. )
Nonlinear taper set ( When “NON-LINEAR” is selected.)
X
W
ST
Initial diameter set (When connected to LE -40MD )
% : C N R 2 # # # # m m φ →
T P E R S E T M E N U #
C N R 1 # # # # m m φ → T P R . 1 # # #
A
O U T P U T → # # # %
I I T . D I A . M E N U #
S E T → # # # # m m φ
N
O U T P U T → # # # %
N W R . S E T
S E T → # # # %
E
O U T P U T → # # # %
T P E R S E T
S E T → # # # %
A
T N S N . → # # # # N
I I T . D I A . M E N U #
S E T → # # # # m m φ
N
T N S N . → # # # # N
N W R . S E T M E N U #
S E T → # # # %
E
T N S N . → # # # # N
T P E R S E T M E N U #
S E T → # # # %
A
Reel diameter monitor
(When use reel diameter input or “LINK” is selected in “TPR.DIA” screen.)
Reel diameter monitor
(Y1,Y2,Y3 are displayed when “DIA.” is selected in “Y MODE” screen.)
Measurement length monitor
(Y1,Y2,Y3 are displayed when “LENGTH” is selected in “Y MODE” screen.)
Line velocity monitor
ST
ST
O U T P U T → # # # %
D A . M N T .
D I A . → # # # # m m φ
I
O U T P U T → # # # %
D A . M N T .
D I A . → # # # # m m φ
I
O U T P U T → # # # %
D A . M N T .
L E N G T H → # # # # # m
I
O U T P U T → # # # %
D A . M N T .
L I N E S P E Ε D → # # # # m / m i n
I
T N S N . → # # # . # k g f
D A . M N T .
D I A . → # # # # m m φ
I
Y 1 : Y 2 : Y 3 :
D A . M N T .
D I A . → # # # # m m φ
I
T N S N . → # # # . # k g f
D A . M N T .
L E N G T H → # # # # # m
I
Y 1 : Y 2 : Y 3 :
L N . M N T .
L E N G T H → # # # # # m
E
T N S N . → # # # # N
D A . M N T .
D I A . → # # # # m m φ
I
T N S N . → # # # . # k g f
S D . M N T .
L I N E S P E E D → # # # # m / m i n
P
When connected to LE-40MD.
To Next Page
Loading...
