Muller Elektronik SLURRY-Controller 3.0

Questions and Answers

D
Denise HallSep 5, 2025
Why is the hydraulic axle drive speed too high on my Muller Elektronik SLURRY 3.0?
- M
  Mitchell WellsSep 5, 2025
  If the drive speed is too high for the hydraulic axle drive on the Muller Elektronik Controller, it's because the drive speed of the hydraulic axle drive is too high. Reduce the speed of the hydraulic axle drive.
L
Linda PierceAug 25, 2025
Why does my Muller Elektronik SLURRY 3.0 Controller say speed is too high?
- R
  Rebecca JacobsAug 25, 2025
  If the speed is too high on the Muller Elektronik Controller, it's because the driving speed for this function is too high. Reduce the driving speed to resolve this issue.
O
Oscar Stone Jr.Aug 25, 2025
Why does my Muller Elektronik Controller say speed is too low?
- D
  David MurrayAug 26, 2025
  If the speed is too low on the Muller Elektronik Controller, it's because a minimum speed is required for the function you want to perform. Increase the speed to resolve this issue.
J
josephmarkSep 13, 2025
What does 'Error - Angle sensor' mean on Muller Elektronik SLURRY 3.0?
- R
  Robyn FinleySep 13, 2025
  If there's an error with the angle sensor on the Muller Elektronik Controller, it means there is a measuring error on the angle sensor. Check the angle sensor.
T
Tiffany CarterSep 23, 2025
Why is the left-hand sensor disabled on my Muller Elektronik SLURRY 3.0 Controller?
- C
  Carlos JonesSep 23, 2025
  If the left-hand sensor is disabled on the Muller Elektronik Controller, it's because the left-hand sensor is disabled. Check the sensor and activate it.
S
Steven WatersSep 9, 2025
What to do if the angle sensor of second element is faulty on Muller Elektronik Controller?
- C
  Corey MillerSep 9, 2025
  If the angle sensor of the second element is faulty or outside of the measurement range on the Muller Elektronik Controller, it's because the sensor is faulty or outside of the measurement range. Check the sensor and replace it if necessary.
L
Levi HayesSep 1, 2025
Why is the gear rotational speed too high on my Muller Elektronik Controller?
- D
  dhardySep 1, 2025
  If the rotational speed of the gear is too high on the Muller Elektronik Controller, it means the gearbox rotational speed is too high. Reduce the rotational speed to resolve this.
L
Lauren MasseySep 23, 2025
Why is the right-hand sensor disabled on my Muller Elektronik SLURRY 3.0?
- D
  Dr. Amber GarciaSep 23, 2025
  If the right-hand sensor is disabled on the Muller Elektronik Controller, it's because the right-hand sensor is disabled. Check the sensor and activate it.
J
jlewisSep 16, 2025
Why is an incorrect change of driving direction detected on Muller Elektronik SLURRY 3.0?
- L
  Laura CherrySep 17, 2025
  If the Muller Elektronik Controller detects an incorrect change of the driving direction for the hydraulic axle drive (expert), it means the driving direction was not recognised by the ISOBUS. Check the driving direction settings.
M
melvin36Aug 28, 2025
What does 'Target Rate is out of reach' mean on Muller Elektronik Controller?
- I
  Ian DunlapAug 28, 2025
  If the Target Rate is out of reach on the Muller Elektronik Controller, it means the control system cannot maintain the target rate. To fix this, drive at a constant speed or control the target rate manually.