NEC P547UL User Manual

4. Using On-Screen Menu
72
NOTE:
• When [HDBaseT] is set, the projector goes into the [SLEEP] mode regardless the setting for the standby mode (→ page 76) on the
on-screen menu is [NORMAL] or [NETWORK STANDBY]. Based on this, the projector can be powered ON by an HDBaseT transmission
device that is connected to the projector when the projector is in the standby mode. However, the standby mode setting cannot
be changed when [HDBaseT] is set.
• While [HDBaseT] is set for the [SERIAL PORT], power consumption in the standby mode becomes not to satisfy the energy saving
regulation.
TIP:
• When controlling the projector using the LAN port, this works with either setting.
Turning On or O Remote Sensor [REMOTE SENSOR]
Set the remote control sensors on the projector’s front and rear panels and the HDBaseT remote
control sensor.
The options are: [ALL], [FRONT/BACK], [FRONT], [BACK], and [HDBaseT].
TIP:
• If the remote control system does not function when direct sunlight or strong illumination strikes the remote control sensor of the
projector, change another option.
• The remote control sensor on the back of the projector cannot be used when the separately sold cable cover is mounted on the
projector.
Setting ID to the Projector [CONTROL ID]
You can operate multiple projectors separately and independently with the single remote control
that has the [CONTROL ID] function. If you assign the same ID to all the projectors, you can conve-
niently operate all the projectors together using the single remote control. To do so, you have to
assign an ID number to each projector.
CONTROL ID NUMBER Select a number from 1 to 254 you wish to assign to your projector.
CONTROL ID Select [OFF] to turn o the [CONTROL ID] setting and select [ON] to turn on the [CONTROL ID]
setting.
NOTE:
• When [ON] is selected for [CONTROL ID], the projector cannot be operated by using the remote control that does not support the
CONTROL ID function. (In this case the buttons on the projector cabinet can be used.)
• Your setting will not be aected even when [RESET] is done from the menu.
• Pressing and holding the ENTER button on the projector cabinet for 10 seconds will display the menu for canceling the Control ID.

NEC P547UL Specifications

General

Native aspect ratio	16:10
Projection distance	0.8 - 12.9 m
Projection technology	3LCD
Contrast ratio (typical)	500000:1
Screen size compatibility	30 - 300 \
Projector native resolution	WUXGA (1920x1200)
Keystone correction, horizontal	-30 - 30 °
Light source type	Laser
Service life of light source	20000 h
Focus	Manual
Focal length range	17.2 - 27.7 mm
Aperture range (F-F)	1.5 - 2.1
Vertical lens shift range	0 - 60 %
Horizontal lens shift range	-29 - 29 %
3D	No
Video color modes	Presentation
Analog signal format system	NTSC 3.58, NTSC 4.43, PAL, PAL 60, PAL M
Supported graphics resolutions	1920 x 1200 (WUXGA), 3840 x 2160
Composite video in	0
HDMI connector type	Full-size
Serial interface type	RJ-45, RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Noise level	26 dB
Certification	CE; EAC; ErP; RoHS; TUEV, TÜV
Projection modes	Ceiling, Front
Number of OSD languages	30
Noise level (economic mode)	22 dB
RMS rated power	20 W
Placement	Ceiling, Desktop
Product type	Standard throw projector
Product color	White
Market positioning	Home cinema
Cable lock slot type	Kensington
Power source	AC
Power consumption (standby)	1.6 W
Power consumption (typical)	293 W
Power consumption (economy mode)	220 W
Recommended gender	Any gender
Storage temperature (T-T)	-10 - 50 °C
Operating temperature (T-T)	5 - 40 °C
Operating relative humidity (H-H)	20 - 80 %
Remote control type	IR

Weight and Dimensions

Depth	407 mm
Width	480 mm
Height	122 mm
Weight	9700 g