Nilfisk-Advance SC800 User Manual (English)

Other manuals for Nilfisk-Advance SC800

Instructions For Use50 pages

User Manual2 pages

Troubleshooting Guide2 pages

User And Maintenance Guide2 pages

How-To3 pages

Questions and Answers:

K
Kim PerryAug 2, 2025
Why is there poor water pick-up with my Nilfisk-Advance Scrubber?
- N
  Nicole LuceroAug 2, 2025
  Poor water pick-up with your Nilfisk-Advance Scrubber can occur due to several reasons. Here's what you can check: * **Worn or torn squeegee blades:** Reverse or replace them. * **Squeegee out of adjustment:** Adjust the squeegee so the blades touch the floor evenly. * **Recovery tank full:** Empty the recovery tank. * **Recovery tank drain hose leak:** Secure the drain hose cap or replace it. * **Recovery tank cover gasket leak:** Replace the gasket or properly seat the cover. * **Debris caught in squeegee:** Clean the squeegee tool. * **Vacuum hose clogged:** Remove any debris. * **Using too much solution:** Adjust the solution flow at the control panel. * **Foam filter cover not seated:** Ensure the cover is seated properly.
J
jasonparkerAug 6, 2025
What to do if my Nilfisk-Advance Scrubber has inadequate solution flow?
- K
  Kimberly HarrisAug 6, 2025
  If your Nilfisk-Advance Scrubber has inadequate solution flow, it could be due to a few reasons: * The solution tank might be empty. Fill the solution tank. * The solution lines, valves, filter, or trough could be clogged. Flush the lines and trough, and clean the solution filter. * The solution shutoff valve might be closed. Open the solution shutoff valve. * There might be a problem with the solution solenoid valve. Clean or replace the valve.
P
padillalindaAug 10, 2025
Why Nilfisk-Advance Scrubber has poor scrubbing performance?
- T
  Tracy FoxAug 10, 2025
  If your Nilfisk-Advance Scrubber isn't scrubbing well, consider these possibilities: * The brush or pad may be worn. Rotate or replace the brushes. * You might be using the wrong type of brush or pad. Consult Advance for the correct type. * You might be using the wrong cleaning chemical. Consult Advance for the appropriate chemical. * You might be moving the machine too fast. Slow down your pace. * You might not be using enough solution. Increase the solution flow at the control panel.
K
Kurt ChavezAug 15, 2025
What to do if my Nilfisk-Advance SC800 Scrubber machine does not run?
- J
  Johnny WilliamsAug 15, 2025
  If your Nilfisk-Advance Scrubber isn't running, check the following: * Ensure the battery connector is connected. * Check for a tripped 10 Amp circuit breaker; look for an electrical short circuit and reset it.
D
Debra TorresAug 18, 2025
What to do if there is no detergent flow in my Nilfisk-Advance SC800 Scrubber?
- M
  Mario WhitneyAug 19, 2025
  If there's no detergent flow in your Nilfisk-Advance Scrubber (EcoFlex models only), consider these causes: * The detergent cartridge may be empty. Fill the detergent cartridge. * The detergent flow line may be plugged or kinked. Purge the system and straighten any kinks in the lines. * The dry seal cap on the detergent cartridge may not be sealed. Reseat the dry seal cap. * The detergent pump wiring may be disconnected or backwards. Connect or reconnect the wiring.
S
schneiderlauraAug 23, 2025
Why Nilfisk-Advance SC800 Scrubber has no FWD/REV wheel drive?
- Q
  qbruceAug 23, 2025
  If your Nilfisk-Advance Scrubber has no FWD/REV wheel drive, check these: * Check for a tripped 30 Amp circuit breaker. Look for a drive motor overload. * Ensure the Emergency Stop Switch is not tripped; reset it if necessary.
C
Christopher RomeroAug 28, 2025
Why Nilfisk-Advance SC800 Scrubber has poor sweeping performance?
- J
  James LopezAug 28, 2025
  If your Nilfisk-Advance Scrubber (Cylindrical System) has poor sweeping performance: * The hopper might be full. Empty and clean the hopper. * The brushes may be worn. Replace the brushes. * The bristles may have taken a set. Rotate the brushes.

Nilfisk-Advance SC800 Specifications

General

Model	SC800
Type	Walk-behind scrubber
Power Source	Battery
Weight	677 lb (307 kg)
Sound level	68 dBA
Noise level	68 dBA
Brush motor	0.75 HP
Brush motor power	0.75 HP