Nilfisk-Advance SC3500

Other manuals for Nilfisk-Advance SC3500

Questions and Answers:

G
gonzaleztylerAug 16, 2025
Why is my Nilfisk-Advance Scrubber floor not drying properly?
- D
  Daniel AlexanderAug 16, 2025
  If your Nilfisk-Advance Scrubber isn't drying the floor sufficiently, several factors could be at play. Ensure the recovery tank isn't full; if it is, empty it. Check the drain hose and squeegee connection, ensuring they are correctly connected. A blocked float ball filter can also cause this issue, so clean it and check its position. Inspect the squeegee for dirt or wear. Also, verify that the recovery tank cover is properly closed and the gasket isn't damaged, and that the bend tube is free from clogs. Finally, a dirty recovery tank can reduce suction, so clean it thoroughly.
A
asummersAug 19, 2025
What to do if Nilfisk-Advance SC3500 machine does not go forward or backward?
- R
  Robert SpenceAug 19, 2025
  If your Nilfisk-Advance Scrubber isn't moving forward or backward, there could be several reasons: * A fault in the control circuit board, which would require replacement. * A problem with the drive motor controller. Refer to “DRIVE MOTOR ERROR INDICATOR INFORMATION”. * The operator not being on the seat; make sure you are seated. * The squeegee is not lifted during backward movement; lift the squeegee when reversing.
S
Sherry RoblesAug 22, 2025
What to do if my Nilfisk-Advance Scrubber brush motor does not work?
- L
  Lisa AlvarezAug 22, 2025
  If the brush motor on your Nilfisk-Advance Scrubber isn't working, it could be due to several reasons. First, the control circuit board might be faulty and require replacement. The brush motor could also be overloaded; try using a soft bristle brush suitable for cleaning and reset the brush motor overload protector. Other potential causes include a brush motor contactor fault or worn carbon brushes, in which case you should contact after-sales service. Lastly, check for any obstacles preventing the brush from rotating and clean the brush if necessary.
M
Matthew FloydAug 25, 2025
What to do if the Nilfisk-Advance SC3500 machine does not work and the red battery capacity warning light turns on?
- J
  James WilliamsAug 26, 2025
  If your Nilfisk-Advance Scrubber isn't working and the red battery capacity warning light is on, it means the battery level is too low. You should charge the batteries.
R
Robert MeyerAug 28, 2025
How to troubleshoot insufficient solution supply to the brush plate of Nilfisk-Advance SC3500?
- M
  Marcus HendersonAug 28, 2025
  If your Nilfisk-Advance Scrubber isn't supplying enough solution to the brush plate, start by checking the solution filter for dirt and clean it if necessary. Also, check if the solution tank empty indicator is on, and if so, fill the solution tank. Lastly, ensure the solution tank isn't too dirty; if it is, clean it thoroughly.
T
terrelltylerAug 31, 2025
What to do if the drive motor of my Nilfisk-Advance SC3500 does not work?
- D
  Dr. Alison Anderson MDAug 31, 2025
  If the drive motor on your Nilfisk-Advance Scrubber isn't working, check if the drive motor trouble light is on and refer to “DRIVE MOTOR ERROR INDICATOR INFORMATION”. Also, the drive motor might be overloaded; reset the drive motor overload protector and check the drive motor/circuit.
T
Troy PatelSep 3, 2025
What causes squeegee to leave scratches on the floor with Nilfisk-Advance SC3500?
- M
  Michelle HarveySep 3, 2025
  If the squeegee on your Nilfisk-Advance Scrubber is leaving scratches on the floor, it could be due to a few reasons. Check for any debris under the squeegee blade and remove it. Inspect the squeegee blades for wear, cracks, or aging, and replace them if necessary. The squeegee balance may also need adjustment.
C
charrisSep 6, 2025
Why won't the motors on my Nilfisk-Advance SC3500 turn on, and no warning light appears?
- J
  James MathisSep 6, 2025
  If the motors on your Nilfisk-Advance Scrubber aren't working and no warning light is on, it could be due to a disconnected battery connector; ensure it is properly connected. Alternatively, the batteries might be completely discharged; in this case, charge the batteries.
J
Jorge HudsonSep 9, 2025
What causes vacuum motor of Nilfisk-Advance SC3500 not to work?
- K
  Kathy MillerSep 9, 2025
  If the vacuum motor on your Nilfisk-Advance Scrubber isn't working, it could be due to a vacuum motor overload; reset the vacuum motor overload protector and check the vacuum motor. Another possibility is a fault in the relay of the vacuum motor, or a control board fault, in which case you should contact after-sales service or replace the control board, respectively.
R
Rebekah DavisSep 12, 2025
What to do if drive motor brake fails on Nilfisk-Advance SC3500 Scrubber?
- P
  phillipsjasonSep 12, 2025
  If the drive motor brake fails on your Nilfisk-Advance Scrubber, it might be because the brake is locked. Try to set the brake unstuck.

Nilfisk-Advance SC3500 Specifications

General

Model	SC3500
Power Source	Battery
Voltage	24 V
Brush Motor Power	2 x 0.75 kW
Noise Level	68 dB(A)
Drive Speed	6 km/h
Productivity Rate	4, 500 m²/h
Battery Type	Lead-acid
Charging Time	8 h
Type	Ride-On Scrubber