Noble UL30

Other manuals for Noble UL30

Installation, Operation And Service Manual66 pages

Instruction Manual2 pages

Questions and Answers

J
Jasmine LewisSep 9, 2025
Why is the wash temperature not at the required range in my Noble Washer?
- L
  laurapalmerSep 9, 2025
  If the wash temperature in your Noble Washer isn't reaching the required range, there are several potential reasons. The water level might be low, so check it and run a new fill cycle if needed. The RTD setpoint could be too slow; check the fault screen and adjust the wash temperature setpoint. A defective RTD or a defective wash heater could also be the cause, requiring replacement. Lastly, a defective heater contactor R1 might be the issue, and it would also need to be replaced.
S
Sarah HarrisonAug 23, 2025
What to do if no water comes through the rinse arms when the “ON/FILL” switch is depressed in my Noble Dishwasher?
- J
  Jacob WestAug 23, 2025
  If no water comes through the rinse arms when the “ON/FILL” switch is pressed, check the following: * Ensure the water is turned on. If not, turn the water on. * The solenoid valve may be defective. In this case, replace the solenoid valve.
A
Ashley RileyAug 25, 2025
What to do if my Noble Dishwasher doesn’t drain when the “OFF/DRAIN” switch is pressed?
- J
  jonathonclarkAug 25, 2025
  If the machine doesn’t drain when the “OFF/DRAIN” switch is pressed, it could be due to: * A clogged drain solenoid: Remove the obstruction. * A defective motor or motor start relay: Replace it. * A defective drain valve: Replace the valve.
S
Sandra WadeAug 27, 2025
Why is the rinse water not at the required temperature range in my Noble Dishwasher?
- M
  mariarossAug 27, 2025
  If the rinse water is not at the required temperature range, consider the following: * Check that the orange/white wires are connected. See the note in the installation instructions. * The thermometer may be defective: Replace it. * The thermostat may be defective: Adjust the thermostat or replace it if necessary. * The incoming rinse water does not meet the minimum criteria indicated on the machine data plate: Adjust as required.
D
Daniel RichardsonAug 27, 2025
Why is there little or no water coming through the rinse assemblies of my Noble Dishwasher?
- S
  Shawn HoffmanAug 28, 2025
  Little or no water coming through the rinse assemblies can be caused by: * Limed-up rinse heads or piping: Delime the rinse heads. * Low water pressure: Increase the pipe size to the machine and adjust the pressure regulator.
C
Charlene FernandezAug 29, 2025
How to troubleshoot wash temperature not at required reading on thermometer in Noble Dishwasher?
- T
  Tara WattsAug 29, 2025
  If the wash temperature is not at the required reading on the thermometer, check the following: * Ensure that the orange/white wires are connected. Refer to the note on page 7. * The thermometer may be defective: Replace it. * The thermostat may be defective: Adjust or replace the thermostat.
K
kphillipsSep 18, 2025
Why doesn't the wash motor operate on delime wash in my Noble UL30 Washer?
- D
  Donna SantiagoSep 18, 2025
  If the wash motor doesn’t operate on delime wash in your Noble Washer, it could be due to several reasons. Check for loose or broken wires in the motor and reconnect or replace them. Verify that the "WASH/DELIME" switch triggers input on the PLC; if not, check the wiring and replace the membrane. A defective motor starting relay could also be the cause, requiring replacement. Finally, the machine might be in FAULT mode and locked out, so review the fault screen for active faults.
P
Patricia VazquezSep 19, 2025
Why is there no indication of pressure in my Noble UL30 Washer?
- S
  Sheri WilliamsSep 22, 2025
  If there is no indication of pressure in your Noble Washer, first ensure that the water is turned on. If the water is on, the pressure gauge may have failed and needs to be replaced.
J
John DaughertySep 8, 2025
What to do if the Noble UL30 Washer machine doesn’t drain when the power button is pressed?
- M
  Marvin MccormickSep 8, 2025
  If your Noble Washer isn't draining when you press the power button, the issue could be a clogged drain. In this case, remove any obstructions. Alternatively, the drain valve might be defective and needs replacement.
M
Melissa JonesSep 5, 2025
What causes motor to operate on manual wash but not on automatic in Noble Dishwasher?
- A
  angela11Sep 5, 2025
  If the motor operates on manual wash but not on automatic, it could be due to: * A defective circuit in the manual wash switch: Replace the switch.