Noble UL30

Other manuals for Noble UL30

Installation, Operation And Service Manual66 pages

Instruction Manual2 pages

Questions and Answers

T
Tristan WilliamsAug 21, 2025
Why is there water overflowing from the bottom of the Noble Dishwasher door?
- K
  Karen KiddAug 21, 2025
  Water overflow from the bottom of the door can occur due to several reasons: * A clogged drain: Remove the obstruction. * The machine is not level: Level the machine or increase the height to the front. * Excessive inlet pressure: Install a pressure-reducing valve or adjust the existing one to ensure the flow is 20 ±5 PSI. * Detergent foaming: Reduce the amount of detergent used.
W
williammartinSep 3, 2025
What causes no indication of pressure in my Noble Dishwasher?
- T
  tpageSep 3, 2025
  If there is no indication of pressure, it could be due to: * The water being turned off: Turn the water on. * A defective pressure gauge: Replace the pressure gauge.
J
Joshua RogersSep 1, 2025
What causes rinse water to run continuously with the breaker turned off in my Noble Dishwasher?
- B
  benderjoshuaSep 1, 2025
  If rinse water runs continuously even with the breaker turned off, it may be due to: * A defective plunger in the solenoid valve: Delime the rinse heads. * A defective diaphragm in the solenoid valve: Replace the diaphragm.
J
jerry27Aug 31, 2025
What causes the wash motor to not operate on manual wash in my Noble Dishwasher?
- L
  Laura MarshallAug 31, 2025
  If the wash motor doesn’t operate on manual wash, it could be due to: * Loose or broken wires: Reconnect or replace the wires in the motor. * A defective manual wash switch: Replace it. * A defective motor starting relay: Replace it.
C
Charlene FernandezAug 29, 2025
How to troubleshoot wash temperature not at required reading on thermometer in Noble Dishwasher?
- T
  Tara WattsAug 29, 2025
  If the wash temperature is not at the required reading on the thermometer, check the following: * Ensure that the orange/white wires are connected. Refer to the note on page 7. * The thermometer may be defective: Replace it. * The thermostat may be defective: Adjust or replace the thermostat.
D
Daniel RichardsonAug 27, 2025
Why is there little or no water coming through the rinse assemblies of my Noble Dishwasher?
- S
  Shawn HoffmanAug 28, 2025
  Little or no water coming through the rinse assemblies can be caused by: * Limed-up rinse heads or piping: Delime the rinse heads. * Low water pressure: Increase the pipe size to the machine and adjust the pressure regulator.
S
Sandra WadeAug 27, 2025
Why is the rinse water not at the required temperature range in my Noble Dishwasher?
- M
  mariarossAug 27, 2025
  If the rinse water is not at the required temperature range, consider the following: * Check that the orange/white wires are connected. See the note in the installation instructions. * The thermometer may be defective: Replace it. * The thermostat may be defective: Adjust the thermostat or replace it if necessary. * The incoming rinse water does not meet the minimum criteria indicated on the machine data plate: Adjust as required.
A
Ashley RileyAug 25, 2025
What to do if my Noble Dishwasher doesn’t drain when the “OFF/DRAIN” switch is pressed?
- J
  jonathonclarkAug 25, 2025
  If the machine doesn’t drain when the “OFF/DRAIN” switch is pressed, it could be due to: * A clogged drain solenoid: Remove the obstruction. * A defective motor or motor start relay: Replace it. * A defective drain valve: Replace the valve.
S
Sarah HarrisonAug 23, 2025
What to do if no water comes through the rinse arms when the “ON/FILL” switch is depressed in my Noble Dishwasher?
- J
  Jacob WestAug 23, 2025
  If no water comes through the rinse arms when the “ON/FILL” switch is pressed, check the following: * Ensure the water is turned on. If not, turn the water on. * The solenoid valve may be defective. In this case, replace the solenoid valve.