沖データ企業秘密・OkiDataCONFIDENTIAL
45530603TX −111／130
Priority
Status Message Ready
LED
Atten
LED
Function Status level
Error code
Status code
3
To turn off the display, press OK.
Please see HELP for details
In PX753, impossibility of spot color printing is the same as impossibility of custom media
printing.
324 1
2
3
Install %MEDIA_SIZE% in %TRAY%
Please see HELP for details
Off Blink
Printing request is issued to an empty tray.
Load paper.
(It takes a while until the status disappears after you have closed the tray and the lever
lifted.)
Error 491 : Tray1
Error 492 : Tray2
Error 493 : Tray3
Error 494 : Tray4
Error 495 : Tray5
The paper size displaying form of the custom mode is the same as above.
If Media_Size has both portrait and landscape, %MEDIA_SIZE% displays icon which
indicate paper orientation after Paper Size.
Error
491
492
493
494
495
472yy
473yy
475yy
476yy
477yy
324.1
1
2
3
Install %MEDIA_SIZE% in MPTray
Please see HELP for details
Off Blink
Printing request is issued to an empty MPTray.
If it goes through a definite period of time (PU firmware holds time(3 sec)) after a user
placess paper, a printer will lift up the multipurpose tray, and will perform re-feeding.
If a user pushes the OK button before timeout, the printer perform also re-feeding,.
Error 490 : MPTray
In this state, Leisus I/F : corresponding bits of both LFTERR and LFTERR2 should be '0'.
Programmer's note: When the OK button was pressed, the controller (CU) should send
MPTPECLR command to the engine (PU). The engine would clear this state after
receiving that command.
This error is occured, when the MPTray is in the home position and the sensor "PE SNS2"
cannot detect papers.
Error
490
470yy
326 1
2
3
Reset Tray
%TRAY%
Please see HELP for details
Off Blink
Print request was made to Tray, to which Tray Lift Up Error has occurred.
Lift Up Retry will take place when the tray is removed and put back in.
Error 520 : Tray1
Error 521 : Tray2
Error 522 : Tray3
Error 523 : Tray4
Error 524 : Tray5
Error
520
521
522
523
524
40966
328 1
2
3
Remove Excess Paper and Reset Tray
%TRAY%
Please see HELP for details
Off Blink
Print request was made to Tray, which has been detected to have too much paper, or the
cassette is not correctly equipped this printer with.
This status will be cleared when excess paper is removed from that tray and the tray is put
back in.
Error 530 : Tray1
Error 531 : Tray2
Error 532 : Tray3
Error 533 : Tray4
Error 534 : Tray5
Error
530
531
532
533
534
40965
330 1
2
3
Remove Paper
%STACKER%
Please see HELP for details
Off Blink
The printed paper is overfilled on the paper stacker of the printer unit.
Error 480 : Face Down Stacker
Error 484 : Face Up Stacker
Error
480
484
40075
40923
333 1
2
3
Install Paper Cassette
%TRAY%
Please see HELP for details
Off Blink
Indicates that paper feed is unavailable in attempting to print from Tray 1 due to removal of
the paper cassette of Tray 1. (Occurs only when Tray 2 has been installed.)
%TRAY%
Tray1
Error
430
431
432
46012
46013
46015
46016
To Next Page
Loading...
