Oki C911 - Page 75

沖データ企業秘密・OkiDataCONFIDENTIAL 
45530603TX - 75/130
Category1 Category2 Category3 Category4 Item Value Default
機能
Valid
+2
+3
-3
-2
-1
print density/frequency. Change the setting when
background is dark.
White 0
+1
+2
+3
-3
-2
-1
*
With Whitr,ｔo correct variations in print results caused
by temperature/humility conditions and difference in
print density/frequency. Change the setting when
background is dark.
ET
Drum Cleaning On
Off *
Sets whether to rotate the drum in idle prior to printing
in order to reduce horizontal white lines. Be warned
that this will shorten the ID life as much as this rotation.
ET
Transfer Roller
Cleaning
Execute
−
Cleans the secondary transfer roller to prevent it from
causing dirty backside.
Transfer Roller Cleaning is started by the execution of
this menu, and then this menu is exited.
JE
High Humid Mode Mode1
Mode2
Off *
Sets if the paper curl after printing is conspicuous.
Try Mode2 if reduced paper curl effects are not
obtained after settings Mode1.
Setting Mode1 or Mode2 will increase the warm-
up time
and reduce the print speed.
RB
Moisture Control On
Off *
Sets Off/On of Moisture Control Mode.
When set to On, engine performs extra rotation of
drums and fuser on the first print after a certain period
of time.
ET
Narrow Paper
Speed
Normal
Slow *
Sets printing speed to narrow paper.
Normal: Do not change printing speed when printing
narrow paper.
Slow: Change printing speed to slow when printing
narrow paper.
ET
Print Mode Normal
Slow *
For continuous printing, sets whether to enable or
disable the throughput control by space (paper feed
interval) adjustment.
Normal: Performs continuous printing at the configured
image spacing (paper feed interval).
Slow: Enables the throughput control of increasing the
space between images (paper feed interval) for
continuous printing.
ET
Transfer
Setting
Cyan Transfer
Setting
0
+1
+2
+3
-3
-2
-1
* Sets the primary transfer voltage of cyan. ET
Magenta Transfer
Setting
0
+1
+2
+3
-3
-2
-1
* Sets the primary transfer voltage of magenta. ET
Yellow Transfer
Setting
0
+1
+2
+3
-3
-2
-1
* Sets the primary transfer voltage of yellow. ET
Black Transfer
Setting
0
+1
+2
+3
-3
-2
-1
* Sets the primary transfer voltage of black. ET
White Transfer
Setting
0
+1
+2
+3
-3
-2
-1
* Sets the primary transfer voltage of white.
[Conditions for display]
.Five color printer and White is selected in [Admin
Setup]-[Color Setup]-[Spot Color].
ET
Clear Transfer
Setting
0
+1
+2
+3
-3
-2
-1
* Sets the primary transfer voltage of clear.
[Conditions for display]
.Five color printer and Clear is selected in [Admin
Setup]-[Color Setup]-[Spot Color].
ET
DV Roller Cleaning On
Off
* To clean the worn toner around the developing-roller
when user prints low duty.
Adjust the toner disposal threshold.
On: Gives priority to image quality.
Off: Gives priority to toner life.
ET
Admin Setup Network Setup TCP/IP Enable
Disable
* Sets Enable/Disable of TCP/IP Protocol.
Enable: TCP/IP Protocol is available.
Disable: TCP/IP Protocol is not available.
JE
NetBIOS over TCP Enable
Disable
* Sets Enable/Disable of NetBIOS over TCP Protocol.
[Condition for display]
・ "Enable" is selected for "TCP/IP".
JE
EtherTalk Enable
Disable *
Sets Enable/Disable of EtherTalk Protocol.
Enable: EtherTalk Protocol is available.
Disable: EtherTalk Protocol is not available.
JE
IP Address Set Auto
Manual
* Sets the IP address setting method.
【Conditions for display】
"Enable" is selected in "TCP/IP."
JE
IPv4 Address xxx.xxx.xxx.xxx  Sets the IP address.
[Condition for display]
JE
4