Oki C911 - Page 83

沖データ企業秘密・OkiDataCONFIDENTIAL 
45530603TX - 83/130
Category1 Category2 Category3 Category4 Item Value Default
機能
Valid
ISOL5
PC-8TK
Kamenicky
HebrewNC
HebrewOC
PlskaMazvia
ISOL6
Win3.1Heb
Win3.1Cyr
PC-866
Win3.1Grk
PC-869
PC-855
Greek-437
Greek-437Cy
Greek-737
Greek-928
SerboCroat2
Ukrainian
Bulgarian
PC-1004
Win3.1Blt
PC-775
SerboCroat1
PC-858
Roman-9
ISOL9
Greek-8
Win3.1L/G
PC-851Grk
PC-8Grk
Hebrew-7
ISO-Hebrew
Hebrew-8
PC-862Heb
ISO-Cyr
ISO-Grk
PC-866Ukr
ISOL4
Letter O Style Enable
Disable *
Specifies the style that replacesφ(9B) and ¥ (9D)
withφ(ou) and Φ(zero).
(Not available with products for Japan.)
JE
Zero Character Normal
Slashed
* Specifies the style of O (zero).
SLASHED: SLASH ZERO
(Not available with products for Japan.)
JE
Line Pitch 6 LPI
8 LPI
* Sets line spacing
(Not available with products for Japan.)
JE
White Page Skip On
Off *
Sets whether ejecting a blank sheet or not.
Available only when simplex is set.
(Not available with products for Japan.)
JE
CR Function CR
CR+LF
* Sets performance when CR code is received.
(Not available with products for Japan.)
JE
Line Length
80 桁
136 桁
* Specifies the number of characters per line.
(Not available with products for Japan.)
JE
Form Length 11 inch
11.7 inch
12 inch
*L
*A
Specifies the length of paper.
(Not available with products for Japan.)
JE
TOF Position 0.0inch
0.1inch
~
1.0inch
* Sets the position from the top edge of paper.
(Not available with products for Japan.)
JE
Left Margin 0.0inch
0.1inch
~
1.0inch
* Sets the amount of shifting the horizontal print start
position to the right.
(Not available with products for Japan.)
JE
Fit to Letter Enable
Disable
*L
*A
Sets the printing mode that can fit print data, equivalent
to 11 inches (66 lines), in the Letter-size printable area.
(Not available with products for Japan.)
(ODA: "Enable"= default)
JE
Text Height Same
Diff
* Sets height of a character.
SAME: Regardless of CPI, same height
DIFF: According to CPI, character heights
vary.[Existing model compatible]
(Not available with models for Japan)
JE
Continuous Paper
Mode
On
Off *
Sets to Landscape the edit direction of paper supported
by A3 printer.
(Not available with PX711 and models for Japan.)
This menu is designed in consideration of SIDM
continuous-sheet paper (pin-feed, fanfold paper).
Irrespective of an setting specified in the menu for
setting paper orientation, the setting On set in the menu
prints media that can be used on A4 printers, such as
A4 or letter size paper, in portrait orientation, and media
that can be used only on A3 printers, such as A3 size
paper, in landscape orientation.
JE
Color Setup Ink Simulation Off
SWOP
ISO Coated
Japan
* The printer holds its own process simulation engine
within and this engine simulates standard colors in the
printer.This function is enabled only with PS language
jobs.
SWOP: ODA/INTER
ISO Coated: OEL
Japan: JP (ODC)
(This setting assumes the above mode selection.)
JE
UCR Low
Medium
High
* Selects limitation to the toner layer thickness.
If paper curl occurs in dark printing, selecting MEDIUM
or LIGHT sometimes helps reduce curl.
UCR: Under Color Removal.
JE
CMY 100% Density Enable
Disable *
Selects enable/disable 100% output against the
CMY100% TRC compensation. Ordinarily, the TRC
compensation function holds control for appropriate
print density; thus, 100% output is not always enabled.
Selecting ENABLE will enable 100% output in individual
color. The actual print, including the TRC compensation
JE