Oki C911 - Page 84

沖データ企業秘密・OkiDataCONFIDENTIAL 
45530603TX - 84/130
Category1 Category2 Category3 Category4 Item Value Default
機能
Valid
function is limited to an appropriate area. This function
is for a special purpose such as specification in CMYK
color diminution of PS.
CMYK Conversion On
Off
* Setting to “OFF” will simplify the conversion process of
CMYK data, which will reduce the processing time.
This setting is ignored when Ink Simulation function is
used.
JE
Spot Color White
Clear
* Showing the Spot Color information.
The settings will be working after you restart the printer.
If you change the settings by menu operation,the
message prompting you to restart the printer will be
displayed.
【Conditions for display】
．The printer has spot color
PW
Panel Setup Near Life LED Enable
Disable
* Sets up LED display control for the occurrence of a
near life warning of a drum, fuser, or belt.
A near life warning is displayed when Enable is set.
A near life warning is not displayed when Disable is set.
(It is also not output to any of Attention
LED/PJL/MIB/Web.)
A status (life warning) of temporal recovery by opening
and closing the cover in a life error state is not included.
ET
Idle Display Toner Gauge
Paper Size
* Sets up LED lighting control for the occurrence of a
near life warning of a toner, drum, fuser, belt or waste
toner box.
Attention LED is lighted when Enable is set.*
Attention LED is not lighted when Disable is set.
The status (life warning) of temporal recovery by
opening and closing the cover in a life error state is not
included.
* It applies to drums, fusers , belts and waste toner box
only when "Panel Setup" - "Near Life Status" is set to
"Enable." It always applies to toner regardless of the
setting of "Panel Setup" - "Near Life Status."
ET
Idle Display Toner Gauge
Paper Size
* Specify display information in idle Display.
Paper Size: Display paper size of each tray.
Toner Gauge: Display toner gauge.
"Toner Gauge" is default.
ET
Panel Brightness
During Operating
5
~
31 *
Tuning the LCD brightness level of the operator panel.
This brightness level is applied during user operation.
ET
Panel Brightness
While Power Save
0
1
~
5
~
31
*
Tuning the LCD brightness level of the operator panel.
This brightness level is applied, after Panel Backlight
Timer has been expired.
ET
Panel Backlight
Timer
10
~
30
~
300
*
Adjusting time that Panel Brightness While Power Save
applies from last operation.
ET
Front Lamp Mode1
Mode2
Off
* Sets up which front lamp works or not. ET
Time Setup Date Format yyyy/mm/dd
mm/dd/yyyy
dd/mm/yyyy
*(JP1)
*(ODA)
*(OEL)
Sets the date display format.
* The default value varies depending on the destination.
ET
Time Zone -12:00
-11:45
-11:30
-11:15
-11:00
~
-1:00
-0:45
-0:30
-0:15
+0:00
+0:15
+0:30
+0:45
+1:00
~
+12:15
+12:30
+12:45
+13:00
*
Sets the time zone (difference from GMT).
(From -12:00 to +13:00 in units of 15 minutes)
ET
Dayｌight Saving
On
Off *
Sets whether to apply the daylight saving time or not.
On: Sets the clock forward one hour at the moment.
Off: Sets the clock back one hour at the moment.
ET
Time Setting 2000/01/01 00 :00
~
2009/01/01 00 :00
~
2091/12/31 23 :59
*(JP1) Sets the time.
The date is displayed in the format according to the
setting of “Date Format.”
ET
01/01/2000 00 :00
~
01/01/2009 00 :00
~
12/31/2091 23 :59
*(ODA)
01/01/2000 00 :00
~
01/01/2009 00 :00
~
31/12/2091 23 :59
*(OEL)
Power Setup Power Save Enable
Disable
* Sets Enable/Disable of Power Save Mode. ET
Sleep Enable
Disable
* Sets Enable/Disable of Sleep Mode. ET
Auto Power Off Enable
Auto Config
Disable
*
*(ODA)
Set the behavior of Auto Power Off.
Disable: Invalidate to go Off mode by time.
Auto Config: The printer does not go to Off mode when
ET