Oki C911 Product Specification

沖データ企業秘密・OkiDataCONFIDENTIAL 
45530603TX - 85/130
Category1 Category2 Category3 Category4 Item Value Default
機能
Valid
LAN cable is connected, goes to Off mode when USB
or Centro cable is connected.
Enable: The printer goes to Off mode even if LAN cable
is connected.
※The default value is Disable for ODA.
Others Setup RAM Setup Receive Buffer Size Auto
0.5 megabyte
1 megabyte
2 megabyte
4 megabyte
8 megabyte
16 megabyte
32 megabyte
* Sets the size of receive buffer
AUTO: Calculated by the following formula. The size
should be designated by the value smaller than the
calculation result. The minimum: 0.5MB
Formula = ((TM-BM)*0.03+0.5)*const
BM: Base memory size, Min. component resident
memory size of the series
model.(PX741/746PDL/PX756=256MB)
TM: Total memory size, Total RAM memory.Const=1
The maximum selection that Menu displays is equal to
the following formula or smaller
.Formula=TM*0.08*const
PW
Resource Save Auto
Off
0.5 megabyte
1 megabyte
2 megabyte
4 megabyte
8 megabyte
16 megabyte
32 megabyte
*
Sets the size of resource saving area.
AUTO: Calculated by the following formula.
This size should be designated by the value smaller
than the calculation result.
The minimum: 0.5MB
Formula = ((TM-BM)*0.03+0.5)*const
BM: Base memory size, Min. component resident
memory size of the series
model.(PX741/746PDL/PX756=256MB)
TM: Total memory size, Total RAM memory.Const=1
The maximum selection that Menu displays is equal to
the following formula or smaller.
Formula=TM*0.08*const
This Menu is valid when PCL and other PDL emula
tions
except PCL are enabled.
PW
Flash Memory
Setup
 Initialize Execute - Initializes Flash Memory.
When the OK switch is pressed, the following
confirmation message appears.
Are You Sure? Yes/No
If No is selected, the previous menu display resumes.
If Yes is selected, the following confirmation message
appears.
Execute Now? Yes/No
If No is selected, the previous menu display resumes.
At this time, the request to execute Flash Memory
ini
tialization is put into the memory and initialization will
be executed at power cycle. If Yes is selected, reboot
takes place, and Flash Memory is initialized at
rebooting cycle.
[Condition for display]
・ "Yes" is selected in "Admin Setup"-"Others
Setup"-"Storage Common Setup"-"Enable Initialization"
RB
Resize PS Area nn% [n.n megabyte] - Modifies the area size for PS of Flash Memory.
The actual size indication in MB unit (by 0.1 MB)
follows %.
The data stored in FLASH will be lost. When the OK
switch is pressed, the following confirmation message
appears.
Are You Sure? Yes/No
If No is selected, the previous menu display resumes. If
Yes is selected, the following confirmation message
appears.
Execute Now? Yes/No
If No is selected,
the previous menu display resumes.
At this time, the request to execute FLASH resize is put
into the memory and resize will be executed at power
cycle. If Yes is selected, shutdown takes place, and
FLASH is resized at power Off/On cycle. Menu displays
only items that can be selected.
The value of this menu is not restored to the factory
default value by executing Reset Setting of Admin
Setup - Settings.
[Condition for display]
・ "Yes" is selected in "Admin Setup"-"Others
Setup"-"Storage Common Setup"-"Enable Initialization"
RB
HDD Setup Initialize Execute -
This category is displayed only if a an HDD is installed.
The data stored in the HDD needs to be deleted.The
re-initialization of the partition is not to be executed.
Initializes the HDD to the
factory default setting. Printer
performs partition-
division, and initializes each partition.
When execute this menu, the following confirmation
message appears.
Are You Sure? Yes/No
If No is selected, the previous menu display resumes. If
Yes is selected, the following confirmation message
appears.
Execute Now? Yes/No
If No is selected, the previous menu display resumes.
At this time, the request to execute HDD initialization is
put into the memory and initialization will be executed at
power cycle.
If Yes is selected, shutdown reboot takes place, and an
HDD is initialized at power Off/On rebooting cycle.
[Condition for display]
・HDD insertion
・"Yes" is selected in "Boot Menu"-"HDD
Setup"-"Enable HDD"
・"Yes" is selected in "Admin Setup"-"Others
Setup"-"Storage Common Setup"-"Enable Initialization"
RB
Resize
Partition
PCL nn% nn% 20 Specifies the size of partition.
Specifies a size by ratio to the whole HDD in % (1%
unit) .
nn,mm,ll: 1 - 98 and nn+mm+ll=100
The sizes are displayed in the list of the partition and
can be changed by selecting the partition of which size
is to be changed. If Apply is selected, the following
RB

Oki C911 Specifications

General

Brand	Oki
Model	C911
Category	Printer
Language	English