Oki MC160MFP Maintenance Manual

44292401TH Rev.1
105 /
Oki Data CONFIDENTIAL
ADJUSTMENT/SETTING
12.2.5 LANGUAGE
12.2.6 BUZZER VOLUME
12.2.7 INITIAL MODE
12.2.8 TONER OUT STOP
12.2.9 TONER LOW
Function • Sets the language of the control panel display.
Use • To change the language of the control panel display.
Setting/
procedure
• The default setting is ENGLISH.
“ENGLISH” / FRENCH / GERMAN / ITALIAN / SPANISH / PORTUGUESE
RUSSIAN / CZECH / SLOVAK / HUNGARIAN / POLISH / JAPANESE
NOTE
• The default setting of language is subject to the setting of [PTT SETTING].
Function
• To set the volume of alarms and the beep sounded when a key is pressed.
Use
Setting/
procedure
• The default setting is LOW.
OFF / “LOW” / HIGH
Function
• To set the mode (Copy mode or Fax mode) that the machine starts up in or returns to
after the Control Panel is reset.
Use
Setting/
procedure
• The default setting is COPY.
“COPY” / FAX
Function • Specifies whether to stop or continue printing when a toner empty condition is detected.
Use • To permit printing upon a toner empty condition.
Setting/
procedure
• The default setting is ON.
“ON” / OFF
NOTE
•If [ON] is selected, printing, copying and faxing stop when the toner runs out.
Function • To set whether to display a message when a toner near empty state is detected.
Use • Use this setting to display a message when a toner near empty state is detected.
Setting/
procedure
• The default setting is ON.
“ON” / OFF
12.2.10 AUTO CONTINUE
12.2.11 IMAGE REFRESH
12.2.12 DUPLEX SPEED
12.2.13 CALIBRATION
Function • Select whether or not printing continues when a size error occurs during printing.
Use
• If [OFF] is selected, an error occurs if the size of paper being printed on is different from
the size of paper specified in the printer driver.
• If [ON] is selected, no error occurs if the size of paper being printed on is different from
the size of paper specified in the printer driver.
Setting/
procedure
• The default setting is OFF.
ON / “OFF”
Function • Use this function to perform aging of the toner cartridge, thereby making less noticeable
the faint lines extending in parallel with the main scanning direction occurring at a pitch
of 24 mm.
NOTE
• Execution of the image refresh mode consumes toner.
• This function does not help uneven density at a pitch of 25 mm.
Use
Setting/
procedure
• The default setting is OFF.
ON / “OFF”
Function • To set print speed and image quality for duplex printing.
Use
• If AUTOMATIC is selected, the print speed is automatically selected.
• If SPEED is selected, the print speed has priority; however, the print quality may
decrease.
• If QUALITY is selected, the print quality has priority; therefore, the print speed will
decrease while the print quality may increase.
Setting/
procedure
• The default setting is AUTOMATIC.
“AUTOMATIC” / SPEED / QUALITY
Function • Executes the image stabilization sequence.
Use
• To calibrate the engine when there are print image quality problems.
• To calibrate the engine when the imaging cartridge and 2nd transfer roller are replaced
with new ones.
Setting/
procedure
• The default setting is OFF.
ON / “OFF”
1. Select [MACHINE SETTING] and then [CALIBRATION], and press the Select key.
2. Select [ON] and press the Select key.
3. Image stabilization is executed.
11.2.12 DUPLEX SPEED
11.2.13 CALIBRATION
11.2.11 IMAGE REFRESH
11.2.10 AUTO CONTINUE
11.2.6 BUZZER VALUME
11.2.7 INITIAL MODE
11.2.8 TONER OUT STOP
11.2.9 TONER LOW
11.2.5 LANGUAGE

Oki MC160MFP Specifications

General

Brand	Oki
Model	MC160MFP
Category	All in One Printer
Language	English