How to resolve 'Connect to PC failed' message on my Oki All in One Printer?
If you see the message "Connect to PC failed" on your Oki All in One Printer, it could be due to a changed IP address on the computer, the computer not being turned on, or the computer not being connected to a network. To resolve this, re-register the computer to the machine, ensure the computer is turned on, and verify the network connection.
Why is my Oki All in One Printer unable to scan?
There could be several reasons why your Oki All in One Printer is unable to scan. Ensure the LAN cable was connected before turning the machine on. Verify that the machine's email address is set and correct. Also, check the SMTP, POP3, and DNS server settings. If another job is in progress, wait for it to complete. Follow any on-screen instructions for errors. For network connections, set [Wired] to [Enable] for wired networks. Note that [Wireless(Infrastructure)] and [Wireless(AP Mode)] cannot be enabled simultaneously. If using wireless, ensure you are connected to a wireless access point and that its power is on. Check the wireless access point settings, and try manual or automatic settings, or restart the wireless LAN function. You can also try wireless reconnection by pressing the (SE...
Why is my Oki MC563 All in One Printer unable to copy?
If your Oki All in One Printer is unable to copy, start by ensuring the machine is turned on and has completed its initialization process. Verify that your document is correctly placed. Make sure the paper tray has paper loaded and is properly installed. Use the correct paper size for your document. If [Paper Feed] is set to [Auto], configure the paper tray by pressing the (SETTING) button, then select [Paper Setup] > [Select Tray] > [Copy] and choose the appropriate paper tray, setting it to [ON] or [ON(Prior)]. If you are using duplex copying, ensure the paper is compatible and the settings are correct. The media type for the paper tray should be set to [Plain] or [Recycled] if [Paper feed] is set to [Auto]. Check for and remove any paper jams. Replace any empty toner cartridges, the ima...
Why is my Oki All in One Printer not printing?
If your Oki All in One Printer is not printing, it could be due to several reasons. First, ensure the printer is not in Sleep or Deep Sleep mode by pressing the (POWER SAVE) button. Also, verify that the printer is turned on. Check the LAN or USB cable connections to both the printer and computer. If the connections are secure, try replacing the cable. Make sure the printer is online by pressing the (PRINT) button and selecting [Online]. If an error message appears on the operator panel, investigate it, or press [?] on the operator panel. If the power switch LED lamp quickly flashes, unplug the power cord and contact your dealer. Also, ensure the printer is set as the default printer in your computer's settings. Finally, confirm that the correct output port is selected in the printer drive...
What should I do if the communication quality is low and the fax may not have received correctly on my Oki All in One Printer?
If the communication quality is low and a fax may not have been received correctly on your Oki All in One Printer, turn off the super G3 mode. If there is still a problem in the received fax, contact the other party and have them resend it.
What to do if no wireless devices are connected to my Oki All in One Printer?
If no wireless devices are connected to your Oki All in One Printer: * Make sure that [Wireless(AP Mode)] on the machine is set to [Enable]. * Confirm the SSID/password for the machine and try Manual Setup. * Make a setting in a location near the machine with good visibility. * Note that up to four devices can be connected to the machine via the wireless LAN (AP mode). The fifth device will be rejected. Disconnect at least one device and try again.
How do I stop junk faxes on my Oki All in One Printer?
To block junk faxes on your Oki All in One Printer, press the (SETTING) button on the operator panel and select [Admin Setup] > [Fax Setup] > [Other Settings] > [Block Junk Fax List] > Set [Setting] to [Mode1].
Why is the received fax not printed on the appropriate paper on my Oki All in One Printer?
If the received fax is not printed on the appropriate paper on your Oki All in One Printer, check if you specified any paper type other than [Plain] or [Recycled] in [Media Type]. If so, specify [Plain] or [Recycled] in [Media Type] for the paper type in the tray.
How to fix 'unable to send or receive a fax' on my Oki All in One Printer?
If you are unable to send or receive a fax on your Oki All in One Printer and have installed an IP phone in a broadband environment, press the (SETTING) button on the operator panel, and then select [Admin Setup] > [User Install] > [Super G3] > [OFF].
What to do if my Oki MC563 All in One Printer is unable to send a fax?
If your Oki All in One Printer is unable to send a fax, first, double-check that you are following the correct sending procedure. Verify that you have entered the correct fax number. If using speed dial, print the list to confirm the number's accuracy. Ensure you've selected the appropriate dial type for your region. Check with the recipient to ensure their machine is ready to receive. If the Transmit/Receipt Journal shows error code [23], adjust the [MF(Tone)/DP(Pulse)] setting in [Admin Setup] > [User Install] to match your environment. If error code [26] appears, modify the [PBX Line] setting under [Admin Setup] > [Fax Setup] > [Fax Setting].
Defines WARNING and CAUTION symbols for safety information.
Provides general safety warnings about machine operation and handling.
Details the required environmental conditions and installation space for the machine.
Provides step-by-step instructions for safely unpacking and installing the machine.
Details the correct procedure and safety precautions for connecting the power cord.
Provides instructions for connecting the machine to a network or computer via cable.
Provides detailed steps for connecting the machine to a wireless network.
Guides the installation of necessary printer, scanner, and fax drivers on computers.
Explains the functions and usage of buttons and the display on the operator panel.
Provides detailed instructions and cautions for replacing toner cartridges and image drums.
Offers solutions for various paper jam error codes and procedures.
Provides steps to resolve document jams in the Automatic Document Feeder.
Lists and explains various error messages displayed on the machine's operator panel.
General| Print Technology | LED |
|---|---|
| Print Resolution | 1200 x 1200 dpi |
| Print Speed (Black) | 30 ppm |
| Print Speed (Color) | 30 ppm |
| Functions | Print, Copy, Scan, Fax |
| Copy Speed (Black) | 30 cpm |
| Copy Speed (Color) | 30 cpm |
| Copy Resolution | 600 x 600 dpi |
| Scan Type | Flatbed, ADF |
| Scan Resolution | 600 x 600 dpi |
| Fax Modem Speed | 33.6 kbps |
| Paper Capacity | 250 sheets |
| Maximum Paper Size | A4 |
| Duplex Printing | Yes |
| Automatic Document Feeder (ADF) | 50 sheets |
| Weight | 29 kg |
| Fax Transmission Speed | 3 seconds per page |
| Connectivity | USB, Ethernet, Wireless |
| Mobile Printing | AirPrint, Google Cloud Print |
| Operating System Compatibility | Windows, macOS |
| Monthly Duty Cycle | 60, 000 pages |
To Next Page
