Omron SYSMAC CJ1W-SCU21-V1 User Manual

744
Index
Automatic Detection Release (3000-series), 657
Automatic Detection Set (3000-series)
, 657
AVG Move (H) Times Set (3000-series), 656
AVG Move (L) Times Set (3000-series), 656
AVG Move Interval Set (3000-series)
, 656
Calibration Release, 642
Calibration Set, 642
Continuous Measurement Start (Interrupt) (3000-series)
,
651
Continuous Measurement Start (Interrupt) (4000-series)
,
663
Continuous Measurement Start (Scan) (3000-series)
, 651
Continuous Measurement Start (Scan) (4000-series), 663
Continuous Measurement Termination (4000-series), 664
Data Request (3000-series)
, 652
Data Request (4000-series), 664
Deflection Measurement Start (4000-series), 663
E Unit Set
, 641
Forced Negative Zero (4000-series), 665
Forced Positive Zero (4000-series), 664
Forced Zero Release (4000-series)
, 665
Genera- purpose Command 2 (4000-series), 666
Genera-purpose Command 1 (4000-series), 665
Measurement Condition List Request (3000-series)
, 647
Measurement Condition List Request (4000-series), 661
Measurement Condition Release (3000-series), 647
Measurement Condition Release (4000-series)
, 661
Measurement Condition Set (3000-series), 643
Measurement Condition Set (4000-series)
, 659
Measurement Termination (3000-series), 651
Memory Switch Set, 641
Memory Switch Set 1 (3000-series)
, 654
Memory Switch Set 2 (3000-series), 655
mm Unit Set, 641
Program Number Set (3000-series)
, 643
Settings, 636
Simple AVG Times Set (3000-series)
, 655
Single Run Measurement Start (3000-series)
, 650
Single Run Measurement Start (4000-series), 662
Statistic Processing Calculation Non-execution (3000-se-
ries)
, 652
Statistic Processing Execution (3000-series), 652
Statistic Processing Memory Clear (3000-series)
, 652
Statistic Result Request (3000-series), 653
Zero Run Measurement Start (3000-series), 650
sequences, E5_J Temperature Controller
General-purpose Read, 556
General-purpose Write, 556
Read Heater Current, 555
Read Initial Status
, 555
Read Input Shift Value, 553
Read Output Value, 554
Read Parameters 1
, 551
Read Parameters 2
, 552
Read Process Value, 554
Read Set Point Limit, 554
Save Set Point
, 548
Select Backup Mode, 547
Select Local Mode, 547
Select RAM Write Mode
, 547
Select Remote Mode, 546
Write Input Shift Value, 550
Write Parameters 1
, 548
Write Parameters 2, 549
sequences, E5_K Digital Controller
Execute/Cancel AT
, 499
General-purpose Write
, 497
Genera-purpose Read, 483
Read Alarm Hysteresis, 475
Read Alarm Value
, 469
Read Control Period, 472
Read Cooling Coefficient, 470
Read Dead Band
, 471
Read Hysteresis, 472
Read Input Digital Filter, 475
Read Input Shift Limits
, 476
Read LBA Detection Time, 473
Read Level 0 Parameters, 476
Read Level 1 Parameters 1
, 477
Read Level 1 Parameters 2, 478
Read Level 2 Parameters 1
, 480
Read Level 2 Parameters 2, 481
Read Manual Reset Value, 471
Read MV
, 468
Read MV at Stop Time and at PV Error, 474
Read MV Limits, 474
Read Process Value
, 468
Read Proportional Band, Integral Time, and Derivative
Time
, 470
Read Set Point, 469
Read Set Point during SP Ramp, 468
Read SP Ramp Time Unit and Set Value
, 473
Remote/Local, 498
Run/Stop, 498
Software Reset
, 500
Switch to Level 0 (Software Reset), 497
Switch to Level 1, 500
Write Alarm Hysteresis
, 491
Write Alarm Value, 486
Write Control Period, 488
Write Cooling Coefficient
, 487
Write Dead Band, 487
Write Hysteresis, 488
Write Input Digital Filter
, 491

Omron SYSMAC CJ1W-SCU21-V1 Specifications

General

Brand	Omron
Model	SYSMAC CJ1W-SCU21-V1
Category	Network Hardware
Language	English