Version 1.2.8 - 2020-08-03 3Translation of original instruction
MT50 EN
MT50_GBIVZ.fm
4.3.8 Refill coolant lubricant.....................................................................................................................27
4.4 Electrical connection ....................................................................................................................................27
4.5 First commissioning......................................................................................................................................27
4.5.1 Warming up the machine................................................................................................................28
5Operation
5.1 Safety ...........................................................................................................................................................29
5.2 Control and indicating elements...................................................................................................................29
5.2.1 Control panel ..................................................................................................................................30
5.2.2 Switching elements.........................................................................................................................30
5.3 Switching on the milling-machine.................................................................................................................31
5.4 Switching off the milling-machine.................................................................................................................31
5.5 Inserting a tool..............................................................................................................................................31
5.6 Speed variation vertical-/ horizontal milling ..................................................................................................32
5.6.1 Horizontal milling ............................................................................................................................32
5.6.2 Speed table horizontal milling.........................................................................................................33
5.6.3 Vertical milling.................................................................................................................................33
5.6.4 Speed table vertical milling .............................................................................................................34
5.7 Standard values for cutting speeds..............................................................................................................34
5.8 Manual spindle sleeve feed..........................................................................................................................35
5.8.1 Rough adjustment...........................................................................................................................35
5.8.2 Fine adjustment ..............................................................................................................................36
5.9 Swivelling the milling head ...........................................................................................................................36
5.9.1 Set milling head to the zero position...............................................................................................37
5.10 Raising / lowering the cross table.................................................................................................................37
5.11 Moving the spindle head-holder forward or back .........................................................................................38
5.12 Moving the cross table left or right (X-axis)..................................................................................................38
5.12.1 Manual movement on the X axis ....................................................................................................38
5.12.2 Switch on / off the automatic table feed (X axis).............................................................................39
5.12.3 Switch to the rapid mode ................................................................................................................40
5.12.4 Switching the feed ..........................................................................................................................41
5.13 Moving the cross table forward / back (Y axis).............................................................................................42
5.14 Turning the spindle head-holder...................................................................................................................43
5.15 Conversion to horizontal milling ...................................................................................................................43
5.16 Cooling .........................................................................................................................................................45
6 Maintenance
6.1 Safety ...........................................................................................................................................................47
6.1.1 Measures before repair works ........................................................................................................47
6.1.2 Notes for repair...............................................................................................................................47
6.1.3 Measures before switching on again and after repair measures....................................................47
6.2 Cleaning .......................................................................................................................................................47
6.3 Inspection and maintenance ........................................................................................................................48
6.4 Cooling lubricants.........................................................................................................................................53
6.5 Repair...........................................................................................................................................................53
6.6 Cooling lubricants and tanks ........................................................................................................................54
6.6.1 Inspection plan for water-mixed cooling lubricants .........................................................................55
7 Ersatzteile - Spare parts
7.1 Ersatzteilbestellung - Ordering spare parts ..................................................................................................56
7.2 Hotline Ersatzteile - Spare parts Hotline ......................................................................................................56
7.3 Service Hotline .............................................................................................................................................56
7.4 Elektrische Ersatzteile - Electrical spare parts .............................................................................................56
7.5 Schaltplan - Wiring diagram .........................................................................................................................56
7.6 Säule und Fuß - Column and Base ..............................................................................................................57
7.7 Frästisch - Milling table.................................................................................................................................60
7.8 Schaltgetriebe Vertikalfräsen - Transmission gear vertical milling...............................................................63
7.9 Riementrieb Horizontalfräsen - Belt drive horizontal milling.........................................................................66
7.10 Universal Schwenkkopf - Universal swiveling head .....................................................................................69
7.11 Vorschubgetriebe X Achse - X axis feed gear..............................................................................................72
7.12 Schaltplan - Wiring diagram 1-2...................................................................................................................76
To Next Page
Loading...
