To Next PageTo Next PageWhat to do if buttons on the control panel of my Panasonic PT-VZ580 do not work?
If the buttons on the control panel of your Panasonic Projector do not work, check if the [CONTROL PANEL] setting in [CONTROL DEVICE SETUP] is set to [DISABLE].
What to do if my Panasonic Projector shows no image?
If your Panasonic Projector is not displaying an image, here are a few things to check: First, ensure that all connections to external devices are correctly performed and that the input selection setting is correct. Verify that the [BRIGHTNESS] adjustment is not set to the minimum. Confirm that the external device connected to the projector is working properly. Finally, check whether the AV mute function is activated, and if so, deactivate it.
How to display image from computer on Panasonic PT-VZ580 Projector?
If you're having trouble displaying an image from a computer on your Panasonic Projector, check if the cable is too long (for D-Sub cables, it should be 10 m (32'10") or shorter). Also, verify that the external video output on the laptop computer is set correctly. (For example, the external output settings may be switched by pressing the “Fn” + “F3” or “Fn” + “F10” simultaneously. Refer to the user manual provided with your computer, as the method varies depending on the computer type.)
Why Panasonic PT-VZ580 Projector power does not turn on?
If your Panasonic Projector isn't powering on, make sure the power plug is firmly connected to the outlet and that the wall outlet is supplying electricity. Check if the circuit breakers have tripped. Also, verify if the lamp indicator or temperature indicator is lit or blinking, and ensure the lamp cover is securely attached.
What to do if Panasonic Projector remote control does not work?
If the remote control for your Panasonic Projector isn't working, first check if the batteries are depleted and ensure their polarity is correctly set. Make sure there are no obstructions between the remote control and the projector's signal receiver, and that you're using the remote within its effective operation range. Also, check for interference from fluorescent light. Finally, confirm that the [REMOTE CONTROLLER] setting in [CONTROL DEVICE SETUP] is not set to [DISABLE], and verify that the ID number setting operation is correct.
Why is audio from HDMI compatible device not output from my Panasonic Projector?
To resolve audio issues from an HDMI compatible device connected to your Panasonic Projector, set the audio output of the connected device to linear PCM.
Why is the color pale or grayish on my Panasonic PT-VZ580?
If the color on your Panasonic Projector appears pale or grayish, ensure that the [COLOR] or [TINT] settings are correctly adjusted. Check that the external device connected to the projector is properly adjusted. Also, inspect the RGB signal cable for any damage.
Why does video from HDMI compatible device not appear or it appears jumbled on Panasonic PT-VZ580 Projector?
If video from an HDMI compatible device does not appear or appears jumbled on your Panasonic Projector, ensure the HDMI cable is securely connected. Try turning the power of both the projector and the external device off and on. Also, verify that the signal input is compatible with the projector.
Why does image from a computer not appear on my Panasonic PT-VZ580?
If the image from your computer isn't appearing on the Panasonic Projector, check if the cable is too long; for D-Sub cables, it should be 10 m (32'10") or shorter. Also, verify that the external video output on your laptop is set correctly. (The external output settings may be switched by pressing the “Fn” + “F3” or “Fn” + “F10” simultaneously. Refer to your computer's user manual, as the method varies depending on the computer type.)
How to fix fuzzy image on Panasonic PT-VZ580 Projector?
If the image on your Panasonic Projector is fuzzy, first check that the lens cap is removed. Then, verify that the lens focus is correctly set and the projection distance is appropriate. Also, inspect the lens to ensure it is clean, and confirm that the projector is installed perpendicular to the screen.
General| Power source | AC |
|---|---|
| AC input voltage | 100 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (standby) | 8 W |
| Power consumption (typical) | 410 W |
| Matrix size | 0.64 \ |
| Optical axis | 44 % |
| Heat dissipation | 1399 BTU/h |
| Number of colors | 16.78 million colors |
| Native aspect ratio | 16:10 |
| Projection distance | 0.76 - 7.62 m |
| Projection technology | LCD |
| Contrast ratio (typical) | 16000:1 |
| Screen size compatibility | 30 - 300 \ |
| Projector native resolution | WUXGA (1920x1200) |
| Keystone correction, vertical | -25 - 25 ° |
| Keystone correction, horizontal | -30 - 30 ° |
| Focus | Manual |
| Throw ratio | 1.09 - 1.77:1 |
| Zoom capability | Yes |
| Focal length range | 15.3 - 24.64 mm |
| Aperture range (F-F) | 1.6 - 2.12 |
| Lamp type | UHM |
| Lamp power | 280 W |
| Lamps quantity | 1 lamp(s) |
| Light source type | Lamp |
| Service life of light source | 5000 h |
| Service life of light source (economic mode) | 6000 h |
| 3D | No |
| Supported video modes | 480i, 480p, 720p, 1080i, 1080p |
| Analog signal format system | NTSC, NTSC 4.43, PAL, PAL 60, PAL M, PAL N, SECAM |
| Supported graphics resolutions | 640 x 400, 640 x 480 (VGA), 720 x 480, 720 x 576, 800 x 600 (SVGA), 1024 x 768 (XGA), 1152 x 864 (XGA+), 1152 x 870, 1280 x 1024 (SXGA), 1280 x 720 (HD 720), 1280 x 768 (WXGA), 1280 x 800 (WXGA), 1366 x 768, 1400 x 1050 (SXGA+), 1400 x 900, 1600 x 1200 (UXGA), 1600 x 900, 1680 x 1050 (WSXGA+), 1920 x 1080 (HD 1080), 1920 x 1200 (WUXGA) |
| Placement | Desktop, Ceiling |
| Product type | Standard throw projector |
| Product color | White |
| Housing material | Plastic |
| Cable lock slot type | Kensington |
| RMS rated power | 10 W |
| Number of built-in speakers | 1 |
| Noise level | 37 dB |
| Noise level (economic mode) | 35 dB |
| Dot clock scanning frequency | 162 MHz |
| Operating altitude | 0 - 2700 m |
| Operating temperature (T-T) | 0 - 40 °C |
| Operating relative humidity (H-H) | 20 - 80 % |
| Ethernet LAN data rates | 100 Mbit/s |
| Serial interface type | RS-232C |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| S-Video inputs quantity | 0 |
| Harmonized System (HS) code | 85286200 |
Weight and Dimensions| Depth | 332 mm |
|---|---|
| Width | 389 mm |
| Height | 125 mm |
| Weight | 4800 g |
Essential safety guidelines for handling, installation, and operation of the projector.
Introduces the projector body and remote control layout and features.
Instructions for inserting batteries and using the remote with multiple projectors.
Covers installation modes, angle sensor, and projector setup options.
Guides on connecting external devices and understanding terminal pin assignments.
Step-by-step guide for connecting power, turning on/off, and understanding indicators.
Covers selecting input signals and adjusting image state like zoom and focus.
Details on using remote functions like mute, freeze, auto setup, and zoom.
Explains how to navigate the menu, access sub-menus, and adjust settings.
Details on adjusting picture mode, contrast, brightness, color, tint, and sharpness.
Covers keystone, screen adjustment, and image shifting for optimal display.
Settings for on-screen display elements, color adjustments, and signal levels.
Instructions for connecting the projector to a network via LAN for remote control.
Details on accessing and controlling the projector through a web browser.
Explains indicator status codes for lamp and temperature issues.
Procedures for cleaning the projector and replacing components like the air filter.
Guide to diagnosing and resolving common projector problems.
Includes PJLink protocol, control commands, and serial communication details.
Provides physical dimensions of the projector.
Safety instructions and specifications for ceiling mounting.
